West Control Solutions ProVU 4 User Manual

West Control Solutions Equipment

Table of contents

Document Outline

Introduction
Installation
- Unpacking
- Installation
- Panel-Mounting
- Cleaning
-Field Upgrade Options
- Options Modules and Functions
- Preparing to Install or Remove Options Modules
- Removing/Replacing Option Modules
- Replacing the Instrument in its Housing
- Auto Detection of Option Modules
- Replacement of Power Supply or Input Boards
- Data Recorder Board
- Profiler Enabling
Electrical Installation
- Installation Considerations
- AC Power Wiring - Neutral for 100 to 240V AC versions
- Wire Isolation
- Use of Shielded Cable
- Noise Suppression at Source
- Sensor Placement Thermocouple or RTD
- Thermocouple Wire Identification Chart
- Connections and Wiring
Powering Up
- Powering Up Procedure
- Front Panel Overview
- Display
- LED Functions
- Keypad
Messages and Error Indications
- Start-up Errors
- Configuration Problem
Input Problems
Un-Calibrated Input Detection
PV Over-range or Under-range Indication
Auxiliary Input Over-range or Under-range Indication
USB Data Transfer Problems
Getting Help
Second Level Support
Third Level Support
Configuration and Use
- Operation Mode
- Main Menu
  - Entry into the Main Menu
    - Navigating the Main Menu
  - Unlock Codes
- Setup Wizard
  - Manual entry to the Setup Wizard
    - Navigating in the Setup Wizard
- Supervisor Mode
  - Entry into Supervisor Mode
    - Navigating in Supervisor Mode
- Configuration Menu
  - Entry into the Configuration Menu
    - Navigating the Configuration Menu
- Input Configuration Sub-Menu
- Control Configuration Sub-Menu
- Output Configuration Sub-Menu
- Alarm Configuration Sub-Menu
- Communications Configuration Sub-Menu
- Recorder Configuration Sub-Menu
- Clock Configuration Sub-Menu
- Display Configuration Sub-Menu
- Lock Code View
- Navigating Lock Code View
Lost Lock Codes
- Forcing Lock Code View
Resetting To Defaults
Automatic Tuning Menu
Profiler Setup Menu
Profiler Control Menu
USB Menu
Recorder Menu
Product Information Mode
Service Information Mode
The USB Interface
- Using the USB Port
  - USB Memory Stick Folders & Files
The Data Recorder Option
- Introduction
- Changes To Operation Mode
- Memory Use Bar Graph
The Profiler Option
Profiler Enabling
Profile Components
Profile Starting & Standard Segments
Loops Segments
Profile Running / Holding vs. Hold Segments
The Auto-Hold Feature
Profile Cycles & Repeat Sequences
Power/Signal Lost Recovery Actions
Profile End Actions
Profile Abort Actions
Manually Tuning Controllers
- Single Control Tuning PID with Primary Output only
- Dual Control Tuning PID with Primary and Secondary Outputs
- PI Tuning Valve, Damper& Speed Controller
- Fine Tuning.
Serial Communications
- Supported Protocols
- RS485 Configuration
Ethernet Configuration
Supported Modbus Functions
Function Descriptions
Function 06 - Write Single Register
Function 08 - Loopback Diagnostic Test
Function 16 - Write Multiple Registers 0x10 Hex
Function 23 Hex - Read / Write Multiple Registers 0x17 hex
Exception Responses
Modbus Parameters
Universal Process Input Parameters
Option Slot A Parameters
Option Slot B Parameters
Option Slot 1 Parameters
Option Slot 2 Parameters
Option Slot 3 Parameters
Option Slot 4 Parameters
Setpoint Parameters
Control Parameters
Alarm parameters
Recorder & Clock Parameters
Display Parameters
Profiler Control & Status Parameters
Profile Setup Over Modbus
Instruction Sequence to create a profile at a specified profile position
Instruction Sequence to edit an existing Profile Header
Instruction Sequence to read a profile
Creating Or Editing A Profile Header
Creating, Editing or Inserting Segments
Segment Data
Deleting Profiles
Delete A Segment
Get Segments Remaining
Edit Response Message From Instrument
Command Response Data
Read A Profile Header
Read A Segment
Segment Data
Read Profile Name
Read Profile Memory Status
Read Profile Status
Instrument Data
Calibration
- Calibration Reminder
- Equipment Required For Checking or Calibrating the Universal Input
- Calibration Check
- Recalibration Procedure
Appendix 1 – Glossary of Terms Used
PC SOFTWARE
- Using The Software
- Instrument Configuration
- Configuring Supervisor Mode
- Configuring Enhanced Operator Mode
Profile Creation And Editing
Changing the Start-up Splash Screen
Changing the Alternate Display Language
Instrument Simulation
Configuring The Connection
Network Configuration For Modbus TCP Options
Instrument Details
Edit Modbus Settings
Fixing An IP Address
Appendix 2 - Specifications
- Universal Process Input
- Auxiliary Inputs
- Auxiliary Input Performance
Digital Inputs
Digital Input Performance
Output Specifications
Single Relay Output Performance
Dual Relay Output Performance
Quad Relay Output Performance
Single Dual SSR Driver Output Performance
Dual SSR Driver Output Performance
Triac Output Performance
DC Linear Output Types & Ranges
DC Linear Output Performance
24V Transmitter Power Supply Performance
Communications
PC Configuration Socket
RS485
Ethernet
USB Socket
Display
Control Loop
Data Recorder
Profiler
Alarms
Conditions For Use
Operating Conditions
Standards
Dimensions
Appendix 3 - Product Coding