Extron Electronics ISM 824 - Manual (Page 90)

SIS ™ Programming and Control, cont’d
ISM 824 Integration Scaling Multiswitcher • SIS ™ Programming and Control 4-4
] = CR/LF (carriage return/line feed) (hex 0D 0A)
} = CR (no line feed)
• = Space
| = Pipe (vertical bar) character
E
= Escape key
X!
= Input number 1 through 8
X!
= 0 to untie only
X!
= 1 to 8, for picture controls,
X@
= Output selection (1 to 8)
X#
= Input Video format:
1 = RGB 4 = YUVi
2 = YUV-HD 5 = S-video
3 = YUVp 6 = Composite
X$
= Horizontal start (0 to 255)
X%
= Vertical start (0 to 31 or 0 to 255, depends on input format)
X^
= Pixel sampling phase (0 to 31)
X&
= Total pixels (Range depends on input resolution ± 128)
X*
= Active pixels (Range depends on input resolution ± 128)
X(
= Active lines (Range depends on input resolution ± 128)
X1)
= 0 = off, or 1 = on
X1!
= Input signal standard (0 through 4)
0 = none 4 = NTSC 4.43
1 = YUVi (50 Hz) 5 = SECAM
2 = YUVi (60 Hz) 6 = PAL
3 = NTSC 3.58 - = Not applicable
X1@
= Internal temperature (in degrees Fahrenheit)
X1%
= Picture adjustment (0 to 255)
X1^
= Horizontal/Vertical position
(zero location is 2048, limits are ± 2047)
X1&
= Horizontal and Vertical size (1 to 4095)
X2)
= Test pattern type
0 = Off 6 = Alternating pixels
1 = Color Bars 7 = Crop
2 = 4:3/16:9 crosshatch 8 = 4.:3/16:9 Film
aspect ratio 1.33
3 = 4x4 crosshatch 9 = 4.:3/16:9 Film
aspect ratio 1.78
4 = Gray scale 10 = 4.:3/16:9 Film
aspect ratio 1.85
5 = Ramp 11 = 4.:3/16:9 Film
aspect ration 2.35
X2! = Output resolution (ISM RGB):
01 = 640x480 13 = 1400x1050
02 = 800x600 14 = 1600x1200
03 = 852x480 15 = 480p
04 = 1024x768 16 = 576p
05 = 1024x852 17 = 720p
06 = 1024x1024 18 = 1080i
07 = 1280x768 19 = 1080p
08 = 1280x1024 20 = 1280x800
09 = 1360x765 21 = 1440x900
10 = 1365x768 22 = 1680x1050
11 = 1366x768 23 = 1920x1200
12 = 1365x1024 24 = 1080pSharp
X2!
= Output resolution (ISM DVI):
01 = 40x480 13 = 1400x1050
02 = 800x600 14 = 1600x1200
03 = 852x480 15 = 480p
04 = 1024x768 16 = 576p
05 = 1024x852 17 = 720p
06 = 1024x1024 18 = 1080i
07 = 1280x768 19 = 1080p
08 = 1280x1024 20 = 1280x800
09 = 1360x765 21 = 1440x900
10 = 1365x768 22 = 1680x1050
11 = 1366x768 23 = 1920x1200
12 = 1365x1024 24 = 1080pSharp
X2!
= Output resolution (ISM HDSDI):
17 = 720p 19 = 1080p
18 = 1080i
X2!
= Output resolution (ISM VS):
01 = 640x480 11 = 1366x768
02 = 800x600 12 = 1365x1024
03 = 852x480 13 = 1400x1050
04 = 1024x768 15 = 480p
07 = 1280x768 16 = 576p
08 = 1280x1024 17 = 720p
09 = 1360x765 18 = 1080i
10 = 1365x768 19 = 1080p
X2@ = Output refresh rate (ISM RGB):
1 = 50 Hz 4 = 96 Hz
2 = 60 Hz 5 = 100 Hz
3 = 72 Hz 6 = 120 Hz
11 =75 Hz
X2@ = Output refresh rate (ISM DVI):
1 = 50 Hz 7 = 24 Hz
2 = 60 Hz 8 = 25 Hz
3 = 72 Hz 9 = 30 Hz
11 =75 Hz
X2@ = Output refresh rate (ISM HDSDI):
1 = 50 Hz 8 = 25 Hz
2 = 60 Hz 9 = 30 Hz
7 = 24 Hz 10 = 59.94 Hz
X2@ = Output refresh rate (ISM VS):
1= 50 Hz 1 = 60 Hz
X2$ = Output sync format:
0 = RGBHV (default) 3 = Y, R-Y, B-Y bi-level
1 = RGBS 4 = Y, R-Y, B-Y tri-level
2 = RGsB (Universal Scaler only)
X2%
= User presets (1 to 3)
X2^
= Input preset (1 to 128)
X2(
= Auto Image (0 to 2)
X3!
= Audio level adjustment range (-18 to +24)
X3@
= Audio gain adjustment range (0 to 24)
X3#
= Audio attenuation adjustment range (-18 to 0)
X3$
= Volume adjustment range (0 - 64)
X3& = RGB delay duration 00 to 50 in 0.1 second increments
(0.0 second to 5.0 seconds)
X4$
= Encoder level (0 to 3)
X4% = Group # (for I/O grouping)
0 = no group 1 through 4 = Group #
X4& = Output board status
0 = Not present 1 = Present (working)
2 = Present (not working)
X4* = Sync frequency xxx.xx
(in Hz for vertical, kHz for Horizontal)
X4( = I/O presets (1 to 16), when viewing current tie
X5)
= Card slot (1 to 4)
X5! = Video/Audio mute:
0 = No Mutes 1 = Video mute
2 = Audio Mute 3 = Video and Audio Mute
X5$
= Zoom parameter
ISM 824 specific symbol definitions