Yaskawa Sigma-5 User Manual: Design and Maintenance - Rotary Motors - Manual (Page 182)

5.6 Anti-resonance Control Adjustment Function (Fn204)
5-45
Adjustments
(3) For Fine-tuning After Adjusting the Anti-resonance Control
5.6.3 Related Parameters
Pn160 and Pn161 are set automatically. The other parameters are not set automatically but the respective set
values in the parameters will apply.
Step Display after Operation Keys Operation
1
Press the Key to view the main menu for the
utility function mode.
Use the
or Key to move through the list,
select Fn204.
2
Press the Key to display the “Tuning Mode = 1"
as shown on the left.
Note: If the display does not switch and “NO-OP” is
displayed, take corrective action after checking
the items given in 5.6.1 (1) Before Performing
Anti-Resonance Control Adjustment Function.
3
Press the Key while “Tuning Mode = 1" is dis-
played. The screen shown on the left will appear and
“damp” will blink.
4
Move the cursor with the or Keys and press
the or Keys to set the damping gain.
Note: Increase the damping gain from about 0% to
200% in 10% increments while checking the
effect of vibration reduction. If vibration reduc-
tion is still insufficient at a gain of 200%, can-
cel the setting, and lower the control gain by
using a different method, such as one-parame-
ter tuning.
5
If fine-tuning of the frequency is necessary, press the
Key. The cursor will move from “damp” to
“freq”. If fine-tuning is not necessary, skip step 6 and
go to step 7.
6
Select a digit with or Keys, and press the
or Keys to fine-tune the frequency.
7
Press Key to save the settings.
“DONE” will blink for approx. 2 seconds and “RUN”
will be displayed.
8
Press the Key to complete the anti-resonance
control adjustment function. The screen in step 1 will
appear again.
㧾㨁㧺 ̆㧲㨁㧺㧯㨀㧵㧻㧺̆
㧲㨚㧞㧜㧟㧦㧻㨚㨑㧼㨞㨙㨀㨡㨚
㧲㨚㧞㧜㧠㧦㧭㨂㨕㨎ޓ㧿㨡㨜
㧲㨚㧞㧜㧡㧦㨂㨕㨎ޓ㧿㨡㨜
㧲㨚㧞㧜㧢㧦㧱㨍㨟㨥ޓ㧲㧲㨀
㧾㨁㧺 ̆㧲㨁㧺㧯㨀㧵㧻㧺̆
㨀㨡㨚㨕㨚㨓 㧹㨛㨐㨑 㧩 㧝
㧾㨁㧺 ̆ 㨂㨕㨎 㧿㨡㨜̆
㨒㨞㨑㨝 㧩 㧜㧠㧜㧜 㧴㨦
㨐㨍㨙㨜 㧩 㧜㧝㧞㧜
㧾㨁㧺 ̆ 㨂㨕㨎 㧿㨡㨜̆
㨒㨞㨑㨝 㧩 㧜㧠㧜㧜 㧴㨦
㨐㨍㨙㨜 㧩 㧜㧝㧡㧜
㧾㨁㧺 ̆ 㨂㨕㨎 㧿㨡㨜̆
㨒㨞㨑㨝 㧩 㧜㧠㧜㧜 㧴㨦
㨐㨍㨙㨜 㧩 㧜㧝㧡㧜
㧾㨁㧺 ̆ 㨂㨕㨎 㧿㨡㨜̆
㨒㨞㨑㨝 㧩 㧜㧠㧞㧜 㧴㨦
㨐㨍㨙㨜 㧩 㧜㧝㧡㧜
㧾㨁㧺 ̆ 㨂㨕㨎 㧿㨡㨜̆
㨒㨞㨑㨝 㧩 㧜㧠㧞㧜 㧴㨦
㨐㨍㨙㨜 㧩 㧜㧝㧡㧜
㧾㨁㧺 ̆㧲㨁㧺㧯㨀㧵㧻㧺̆
㧲㨚㧞㧜㧟㧦㧻㨚㨑㧼㨞㨙㨀㨡㨚
㧲㨚㧞㧜㧠㧦㧭㨂㨕㨎ޓ㧿㨡㨜
㧲㨚㧞㧜㧡㧦㨂㨕㨎ޓ㧿㨡㨜
㧲㨚㧞㧜㧢㧦㧱㨍㨟㨥ޓ㧲㧲㨀
Parameter Name
Pn160 Anti-resonance Control Related Switch
Pn161 Anti-resonance Frequency
Pn162 Anti-resonance Gain Compensation
Pn163 Anti-resonance Damping Gain
Pn164 Anti-resonance Filter Time Constant 1 Compensation
Pn165 Anti-resonance Filter Time Constant 2 Compensation