Index, Index-1 – Yaskawa SGDH Linear Sigma Series User Manual

Page 421

Index

Index-1

INDEX

adjusting offset ....................................................................................38
air gap..................................................................................................14
alarm code output........................................................................... 76

alarm display table ................................................................................2
alarm display table when the application module is used.....................5
alarm reset ...................................................................................... 76

alarm traceback data clear (Fn006).....................................................13
alarm traceback data display (Fn000) ...................................................9
allocating input signals........................................................................27
allocating output signals......................................................................29
allowable maximum motor speed and dividing ratio monitor ............34
ALM....................................................................................................28
ALM-RST ...................................................................................... 27

ALO ....................................................................................................28
ambient/storage temperature .................................................................3
analog monitor ....................................................................................29
analog monitor cable...........................................................................10
analog monitoring .................................................................................4
application module..............................................................................10
application module detection results clear (Fn014) ............................19
automatic offset-signal adjustment of motor current detection signal
(Fn00E) ...............................................................................................14
autotuning functions..............................................................................3

base-mounted type ..............................................................................14
bias setting.............................................................................................3
BK .......................................................................................................28
built-in open collector power supply ....................................................3
built-in panel operator...........................................................................2

cable seletion.........................................................................................7
cables for analog monitor....................................................................19
cables for connecting hall sensors

dimensional drawings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9

cables for connecting linear scales

dimensional drawings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8

cables for connecting personal computers ..........................................18
cables for connecting serial converter units

dimensional drawings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7

calculating the required capacity of regenerative resistors ...................4
CE marking .........................................................................................11
checking products .................................................................................2
clear signal form selection ..................................................................48
CLR.....................................................................................................27
CLT .....................................................................................................28
CN1

terminal layout- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26

CN2

terminal layout- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22

coil assembly

model designations- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2

COIN...................................................................................................28

connecting a reactor ............................................................................ 38
connecting linear scales

linear scale by Heidenhain - - - - - - - - - - - - - - - - - - - - - - - - -22
linear scale by Renishaw- - - - - - - - - - - - - - - - - - - - - - - - - - -22

connecting regenerative resistors........................................................ 39
connecting the digital operator ............................................................. 2
connection cable for digital operator .................................................. 10
connection cable for personal computer ............................................. 10
connection to host controller............................................................... 16
connector terminal block converter unit ............................................. 20
connectors and cables for encoder signals .......................................... 10
continuous output current ..................................................................... 2
control method ...................................................................................... 3
control mode selection ................................................................. 29

DATA/ENTER key ............................................................................... 3
DATA/SHIFT key ................................................................................. 3
DC reactors ......................................................................................... 28

selection- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -12

DeviceNet application module............................................................ 31
digital operator............................................................................. 10

key names and functions - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
status display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
types - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2

DOWN key ........................................................................................... 3
DSPL/SET key...................................................................................... 3
dynamic brake....................................................................................... 4

electronic gear....................................................................................... 4
electronic gear ratio equation.............................................................. 51
encoder signal output .......................................................................... 43
external force limit.............................................................................. 69
external regenerative resistor .............................................................. 21

feed forward compensation................................................................... 3
feedback signal checking ............................................................... 9

feed-forward reference........................................................................ 15
flexible cables ..................................................................................... 10

wiring precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -10

force control tolerance .......................................................................... 3
force limit setting ......................................................................... 11

force limiting using an analog voltage reference................................ 71
forward run prohibited ........................................................................ 32
frequency characteristics....................................................................... 3
fuse capacity ....................................................................................... 11

grounding ............................................................................................ 33

hall sensor

selecting no hall sensor- - - - - - - - - - - - - - - - - - - - - - - - - - - -14

hall sensor signal monitor ................................................................... 35
hot start ............................................................................................... 12

I/O signal (CN1) names and functions ............................................... 27
I/O signal cables........................................................................... 10