AMETEK CTS 3.0 - Manual (Page 13)

User Manual Compliance Test System 3.0
9
List of Figures
Figure 3-1: EUT Connection distance and wire gauge. .................................................................. 30
Figure 3-2: Functional Test Setup ................................................................................................... 32
Figure 3-3: Single-phase configuration 5001iX-CTS ...................................................................... 33
Figure 3-4: Single-phase configuration 1251RP-CTS ..................................................................... 34
Figure 3-5: Power Connections for PACS-1 for a single-phase CTS. ............................................ 35
Figure 3-6: Three-phase configuration 15003iX-CTS ..................................................................... 36
Figure 3-7: Power Connections for PACS-3 in a three-phase CTS. ............................................... 37
Figure 3-8: Switch Settings for Remote Impedance Control (Factory Default) ............................... 39
Figure 3-9: Switch Settings for Manual Impedance Control ............................................................ 39
Figure 3-10: Front and Rear Panel Views of the PACS-1 Module. ................................................. 40
Figure 3-11: Front and Rear Panel Views of the PACS-3 Module. ................................................. 41
Figure 3-12: Exacq Control Center Screen. .................................................................................... 46
Figure 3-13: Exacq Card Device Number ....................................................................................... 47
Figure 3-14: Exacq Test Panel ....................................................................................................... 48
Figure 3-15: Exacq DMM Screen .................................................................................................... 49
Figure 3-16: Exacq Scope Test Panel ............................................................................................ 50
Figure 3-17: NI E Series Explorer Panel ......................................................................................... 51
Figure 3-18: Figure 3 .................................................................. 51
Figure 3-19: Jumper and DIP switch location on the A/D Card ...................................................... 53
Figure 3-20: A/D Card JMP 11 Settings .......................................................................................... 54
Figure 3-21: A/D Card JMP 13 Settings .......................................................................................... 54
Figure 3-22: A/D Card Base I/O Address DIP ................................................................................. 56
Figure 5-1: Class D Current Wave Shape Template ...................................................................... 68
Figure 5-2: EUT Class Determination Flowchart ............................................................................ 69
Figure 5-3: Typical Class A test setup ............................................................................................ 71
Figure 5-4: Additonal Settings for Harmonics Test ......................................................................... 73
Figure 5-5: Harmonics Test Window .............................................................................................. 75
Figure 6-1: Flicker Test Window ..................................................................................................... 84
Figure 7-1: IEC 61000-4-11 Test Window ...................................................................................... 92
Figure 7-2: IEC 61000-4-11 Voltage Variation specification- Edition 1.0 ........................................ 93
Figure 7-3: IEC 61000-4-11 Voltage Variation specification- Edition 2.0 ........................................ 93
Figure 7-4: IEC 61000-4-11 Setup screen ...................................................................................... 95
Figure 8-1: IEC 61000-4-13 Test Window ...................................................................................... 98
Figure 8-2: IEC 61000-4-13 Flow Chart Class 1 and 2. ................................................................ 101
Figure 8-3: IEC 61000-4-13 Flow Chart Class 3. .......................................................................... 102
Figure 9-1: IEC 61000-4-14 Test Window .................................................................................... 106
Figure 9-2: IEC 61000-4-14 Test Sequence ................................................................................. 108
Figure 10-1: IEC 61000-4-17 Test Window .................................................................................. 113
Figure 10-2: IEC 61000-4-17 Waveform Acquisition Window ...................................................... 115
Figure 10-3: IEC 61000-4-17 User Observation Data Entry Window ........................................... 116
Figure 11-1: IEC 61000-4-27 Test Window .................................................................................. 117
Figure 12-1: IEC 61000-4-28 Test Window .................................................................................. 123
Figure 12-2: IEC 61000-4-28 Test Sequence ............................................................................... 125
Figure 13-1: IEC 61000-4-29 Test Window .................................................................................. 128
Figure 17-1 : CTS 3.0 Calibration Program Main Screen ............................................................. 148
Figure 17-2: Single Phase Calibration Setup ................................................................................ 150
Figure 17-3: Three Phase Calibration Setup ................................................................................ 151
Figure 19-1: Location of AC Sensor Assy. 5004-700 in PACS-x .................................................. 157