Compex Systems Advanced SerialRAID Adapters SA33-3285-02 - Manual (Page 517)

configuring and installing SSA RAID arrays (continued)
adding a new hot spare pool 83
adding an SSA RAID array 60
adding disks to a hot spare pool 86
canceling all SSA disk drive identifications 129
changing member disks in an SSA RAID array 137
changing or showing the attributes of an SSA RAID
array 135
changing or showing the status of a hot spare
pool 74
changing or showing the use of an SSA disk
drive 144
changing the use of multiple SSA physical
disks 147
creating a hot spare disk drive 72
deleting an old RAID array recorded in an SSA RAID
manager 133
deleting an SSA RAID array 70
getting access to the SMIT menu 59
identifying and correcting or removing failed disk
drives 91
identifying array candidate disk drives 125
identifying hot spare disk drives 121
identifying rejected array disk drives 123
identifying system disk drives 127
identifying the disk drives in an SSA RAID array 119
installing a replacement disk drive 95
listing all defined SSA RAID arrays 100
listing all SSA RAID arrays that are connected to a
RAID manager 102
listing all supported SSA RAID arrays 101
listing array candidate disk drives 115
listing hot spare disk drives 111
listing old RAID arrays recorded in an SSA RAID
manager 131
listing rejected array disk drives 113
listing system disk drives 117
listing the disk drives in an SSA RAID array 109
listing the disks that are in a hot spare pool 80
listing the status of all defined SSA RAID
arrays 104
removing a disk drive from an SSA RAID array 138
removing disks from a hot spare pool 86
showing the disks that are protected by hot
spares 77
swapping members of an SSA RAID array 142
configuring devices on an SSA loop 18
configuring devices, adapter device driver 257
configuring SSA disk drive devices 268, 269
using mkdev to configure a logical disk 269
using mkdev to configure a physical disk 269
configuring the Fast-Write Cache feature 211
configuring the SSA Target mode 292
copying data from an array 151
copying data from arrays and from volume groups 149
correcting or removing failed disk drives 91
couple action attributes, RAID-1 and RAID-10 252
force=yes/no 252
pool_selection=own/primary/secondary 252
creating a hot spare 72
creation and change attributes, all RAID arrays 244
allow_page_splits=true/false 244
bypass_cache-if_oneway 245
fastwrite=on/off 244
fw_end_block 244
fw_start_block 244
fw_suspended 245
creation and change attributes, hot spare pool 249
creation and change attributes, RAID arrays 244
creation and change attributes, RAID-1 and -10
arrays 247
copy_rate 247
copy_verify_writes 247
fw_max_length 247
hot_spare_splits 247
split_resolution 247
creation and change attributes, RAID-1, -5, and -10
arrays 245
read_only_when_exposed=true/false 245
spare_exact=true/false 245
spare_preferred 246
spare=true/false 245
creation and change attributes, RAID-10 arrays 248
strip_size 248
creation and change attributes, RAID-5 arrays 248
fw_max_length 248
strip_size 248
cron table entries 313
D
data paths and loops
examples
broken loop (cable removed) 403
broken loop (disk drive removed) 406
normal loops 401
data paths, loops and links
configuring devices 18
data paths, loops, and links 7
large configurations 16
one loop with two adapters in each of two using
systems 12
one loop with two adapters in one using system 11
simple loop 8
simple loop, one disk drive missing 9
simple loop, two disk drives missing 10
two loops with one adapter 14
two loops with two adapters 15
dealing with fast-write problems 218
dealing with RAID array problems 89
deciding how to configure hot spare disk drive pools 45
Index 497