SATEC SA300 ezPAC Operation Manual User Manual

Ezpac, Operation manual

ezPAC™

SA300 Series

SUBSTATION AUTOMATION UNIT

SA310/SA320/SA330

Operation Manual

BG0346 Rev. A5

Table of contents

Document Outline

Chapter 1 Introduction
- ezPACTM Features
- AC/DC Inputs
- Digital and Analog I/O Options
- Communications Options
- Remote Displays
- Upgradeable Firmware
- Device Models
- Firmware Versions
Chapter 2 Device Description
- Controls and Indicators
  - Device Controls
    - PROGRAM-RUN Key
  - Indicator LEDs
- Modes of Operation
- Communicating with the SA300
- Device Inputs
- Device Outputs
  - Analog Outputs
  - Relay Outputs
- Metering
- Monitoring
- Recording
- Time Synchronization
- Device Diagnostics
  - Device Fault Alarm
Chapter 3 Using the RDM
- Connecting the RDM
- Data Display
- Status Information Display
  - Resetting Counters
  - Resetting Device Diagnostics
- Using the Menus
- Configuring the RDM
- Configuring the SA300
Chapter 4 Using HyperTerminal
- Connecting to the Device
- HyperTerminal Commands
Chapter 5 Using Telnet
- Connecting to the Device
- Telnet Commands
Chapter 6 Using PAS
- Installing PAS
- Installing the USB Driver
  - Windows XP Installation
  - Windows 2000 and Windows 98 Installation
- Creating a New Site for your Device
- Setting up Communications
- Setting Up the Device
Chapter 7 Programming the SA300
- Authorization
- Changing Port Settings
- Basic Device Setup
  - Wiring Connections
- Advanced Device Setup
  - Power Calculation Modes
- Local Settings
  - Time Synchronization Source
  - Daylight Savings Time
- Generating Energy Pulses
  - Generating Energy Pulses through Relay Outputs
- Configuring Digital Inputs
- Programming Relay Outputs
  - Recording Relay Events to the Sequence-of-Events Log
- Programming Analog Inputs
- Programming Analog Outputs
- Using Counters
- Using Periodic Timers
- Using Control Setpoints
Chapter 8 Configuring Recorders
- Configuring Device Memory
- Configuring the Event Recorder
- Configuring the Sequence-of-Events Recorder
- Configuring the Data Recorder
- Configuring the Waveform Recorder
- Configuring the IEEE 1159 Power Quality Recorder
- Configuring the EN50160 Power Quality Recorder
- Configuring the Fault Recorder
Chapter 9 Totalization Energy and TOU Registers
- Configuring Summary and TOU Registers
- Configuring TOU Daily Profiles
- Configuring TOU Calendars
Chapter 10 Configuring Communication Protocols
- Configuring Modbus
  - Modbus Point Mapping
  - Changing Raw Scales for 16-bit Registers
- Configuring DNP3
Chapter 11 Device Control
- Authorization
- Device Mode Control
- Remote Relay Control
- Device Event Flags
- Viewing and Clearing Device Diagnostics
- Updating the Clock
- Resetting Accumulators and Clearing Log Files
Chapter 12 Monitoring Devices
- Viewing Real-time Data
- Viewing Real-time Min/Max Log
- Viewing Real-time Waveforms
Chapter 13 Retrieving Recorded Files
- Uploading Files on Demand
- Using the Upload Scheduler
Chapter 14 Viewing Log Files
- General Operations
- Viewing the Event Log
- Viewing the Sequence-of-Events Log
  - Filtering and Sorting Events
  - Linking to Waveforms, Fault Log and Data Records
- Viewing the Power Quality Event Log
- Viewing the IEEE 1159 Statistics Report
  - Changing the Report Time Range and Contents
  - Customizing Reports
- Viewing EN50160 Statistics Reports
- Viewing the Fault Log
- Viewing the Data Log
  - Viewing Data Trend
- Viewing Waveforms
- Viewing Synchronized Waveforms
Chapter 15 COMTRADE and PQDIF Converters
- Manual Converting
- Automatic Converting
Appendix A Parameters for Analog Output
Appendix B Setpoint Actions
Appendix C Parameters for Monitoring and Data Logging
Appendix D EN50160 Statistics Log Files
Appendix E Data Scales
Appendix F Device Diagnostic Codes