Watlow Series 982 - Manual (Page 137)

WATLOW Series 982 User’s Manual A.7 Appendix
Index Prompt Index
A
[A_50] 6.7
[Addr] address 4.40
[A2HI] alarm 2 high 5.5
[A2LO] alarm 2 low 5.5
[A3HI] alarm 3 high 5.6
[A3LO] alarm 3 low 5.6
[A4HI] alarm 4 high 5.7
[A4LO] alarm 4 low 5.7
[AbSP] abort set point 4.31
[ACAL] retransmit calibration offset
4.27
[`AL2] alarm 2 4.17
[`AL3] alarm 3 4.19
[`AL4] alarm 4 4.22
[Amb] ambient temperature 6.4
[Anun] annunciator 4.32
[Aout] analog output 4.25
[`ArH] retransmit high limit 4.26
[`ArL] retransmit low limit 4.26
[AtSP] auto-tune set point 4.33
[`AUt] auto-tune 5.8
B
[bAUd] baud rate 4.39
[brSt] burst fire 9.2
C
[`C_F] celcius-fahrenheit 4.29
[CAL1] calibration offset 1 4.6
[CAL2] calibration offset 2 4.10
[`Ct1] cycle time, output 1 5.14
[`Ct2] cycle time, output 2 5.17
D
{dAtA} data bits and parity 4.39
[dAtE] date 6.3
[``db] dead band 5.17
[`dE1] derivative, output 1 5.13
[`dE2] derivative, output 2 5.16
[dEC1] decimal 1 4.4
[`dFL] default 6.8
[dISP] test displays 6.6
E
[`Ei1] event input 1 4.30
[Ei1S] event input 1 status 5.3
[`Ei2] event input 2 4.31
[Ei2S] event input 2 status 5.3
[`End] end step (end) 7.4
[Ent3] event 3 7.2, 7.3
{Ent3} event output 3 status 5.4
[Ent4] event 4 7.2, 7.3
{Ent4} event output 4 status 5.4
[`Err] error latching 4.29
F
[FiLE] file 7.1
[Ftr1] software filter 1 4.7
G
[`gSd] guaranteed soak deviation
4.34
H
[`HiP] high power limit 4.33
[Hour] hour 7.2, 7.3
[Hunt] hunt 4.10
[Hys1] hysteresis 1 4.14
[Hys2] hysteresis 2 4.16
[Hys3] hysteresis 3 4.20
[HyS4] hysteresis 4 4.23
I
[IdSP] idle set point 4.36
[`In1] input 1 4.3
[`In2] input 2 4.8
[`It1] integral, output 1 5.12
[`It2] integral, output 2 5.15
[itY1] input 1 module type 6.4
[itY2] input 2 module type 6.4
{IntF} interface type 4.41
J
[``JC] jump count 7.4
[``JF] jump file 7.4
[``JL] jump-loop step 7.4
[``JS] jump step 7.4
L
[LAt2] latching 2 4.17
[LAt3] latching 3 4.21
[LAt4] latching 4 4.24
[LFiL] link file 7.4
[`LOC] lockout 4.37
[`LoP] low power limit 4.32
[LrnH] learn high range 4.9
[LrnL] learn low range 4.9
M
[Min] minutes 7.2, 7.3
O
[`Ot1] output 1 4.13
[`Ot2] output 2 4.15
[`Ot3] output 3 4.18
[`Ot4] output 4 4.22
[OtY1] output 1 module type 6.5
[OtY2] output 2 module type 6.5
[OtY3] output 3 module type 6.5
[OtY4] output 4 module type 6.5
P
[PAUS] pause 9.8
[`Pb1] proportional band, output 1
5.11
[`Pb2] proportional band, output 2
5.14
[Pout] power outage 4.35
[Prc1] process 1 4.14
[Prc2] process 2 4.15
[Prc3] process 3 4.25
[PStr] profile start 4.36
[PtYP] program type 4.34
{Prot} protocol type 4.40
R
[`rA1] rate, output 1 5.13
[`rA2] rate, output 2 5.16
[rATE] rate 7.2
[`rE1] reset, output 1 5.12
[`rE2] reset, output 2 5.15
[`rH1] range high 1 4.5
[`rH2] range high 2 4.9
[`rL1] range low 1 4.5
[`rL2] range low 2 4.8
[`rSt] restore 6.8
[rtd1] RTD 1 4.7
S
[`SEC] seconds 7.2, 7.3
[SHyS] slidewire hysteresis 4.11
[SIL2] silencing 2 4.18
[SIL3] silencing 3 4.21
[SIL4] silencing 4 4.24
[SoAH] soak 7.3
[SOFt] software revision 6.3
[Sn--] serial number 6.3
[``SP] set point 7.2
[StEP] step 7.1
[StPt] set point step 7.2
[StyP] step type 7.2
T
[tout] test outputs 6.6
W
[`WE] waitfor event input 7.3
[WPr] waitfor process crossover
value 7.3