Ac75 at command set – Siemens AC75 User Manual
Page 77
![background image](/manuals/154345/77/background.png)
AC75 AT Command Set
2.14 AT^SCFG
s
AC75_ATC_V01.002
Page 77 of 569
10/30/06
Confidential / Released
• Parameters "GPRS/ATS0/withAttach" (
) and "GPRS/RingOnIncomingData" (
) are avail-
able only for modules supporting GPRS.
Examples
EXAMPLE 1
Usage of "AutoExec":
Enable sending of a short message (SMS) on next DTR activation (OFF-ON transition). Sent SMS is
assumed to be stored at first location of storage selected with
, i.e. SMS may be
sent either from SIM or ME storage.
. Since SMS transmission and ongoing calls are possible at the same
time there is no need to wait until all calls have ended (
=0).
If a DTR activation has occured the ME issues the URC "
" followed by the response of the executed
command; the message reference in this case:
EXAMPLE 2
Usage of "AutoExec":
Configure AC75 to perform a reset every 10 hours. The execution of the reset command shall be deferred
until after any calls have ended.
For details regarding software controlled power down refer to
After ten hours:
EXAMPLE 3
Usage of "AutoExec":
Switch off the ME after three minutes without restarting it.
For details regarding software controlled power down refer to
Please keep in mind that if the GSM alphabet is enabled special characters within the executed AT command
AT+CMGF=1
Enable SMS text mode.
OK
AT+CNMI=1,1
Enable "+CMTI:" URC to be indicated when a short
message is received.
OK
AT+CMGD=1
Delete first SMS location.
OK
AT+CMGW="01522400045",145
Start writing a short message.
>Test-SMS to be sent from storage!
Enter the text of the message. Finish with CTRL-Z.
+CMGW: 1
Confirms that message is stored to first location.
OK
AT^SCFG="AutoExec",1,0,0,0,"AT+CMSS=1"
Enable execution on next DTR activation.
^SCFG: "AutoExec","1","0","0","0","at+cmss=1"
^SCFG: "AutoExec","0","1","0","0","","000:00:00","000:00:00"
^SCFG: "AutoExec","0","1","1","0","","000:00:00","000:00:00"
^SCFG: "AutoExec","0","1","2","0","","000:00:00","000:00:00"
OK
^SCFG:"AutoExec",0,0,1,0,"AT+CMSS=1"
OK
Confirms that AT+CMSS=1 has been issued.
+CMSS: 16
AT^SCFG="AutoExec",1,1,2,5,"AT+CFUN=0,1","010:00:00"
...
OK
^SCFG:"AutoExec",1,1,2,5,"AT+CFUN=0,1"
OK
Confirms that AT+CFUN=0,1 has been issued.
SYSSTART
AC75 has restarted. Remember that the
"^SYSSTART" URC will not appear if autobauding is
enabled.
- A75
- SXG75
- CX65
- A50
- C30
- A65
- SL75
- A35
- M75
- SX1
- C55
- M55
- SL45
- S65
- S75
- CF75
- CFX65
- AX75
- C75
- M65
- CX75
- ST60
- U15
- CF62
- C45
- C45
- Xelibri 8
- Xelibri 7
- SL45i
- SL42
- Xelibri 3
- ST55
- SL55
- C62
- C62
- Xelibri 6
- M50
- Xelibri 2
- Xelibri 4
- A57
- A36
- Xelibri 1
- Xelibri 5
- C70
- Gigaset SL 740
- Mobile Phone C35i
- 4110
- RS-485
- A55
- Gigaset SL55
- Gigaset C450 IP
- Gigaset E45
- S42
- Gigaset 150
- XT75
- SL370
- M30
- A40
- S56
- TDMA 800
- S40
- 150 H
- MT50
- C60
- SL 42
- CL50
- 1168
- C35i
- A52
- SL56
- A60
- SX66
- 4000
- MOVIEMATE 50
- XT55 AVL
- XT55
- 3000
- Gigaset 200
- Mobile
- Mux_guide_v06
- Gigaset S450 IP
- MC60
- Hicom 300E
- SF65
- CXV70
- CXV65
- 8WD44
- C61
- C56
- S45i
- MC55
- CX70
- PEGASUS-DTC AX72
- C70 CT70
- 4010
- Gigaset SL1
- Gigaset C100 DECT
- Gigaset S1
- 4000i
- Gigaset 3000 Classic