HP Anab EQ5 - Manual (Page 50)

EQ5 AC Drive Operations Manual
_______________________________________________________________________
TECO – Westinghouse Motor Company Parameters C20 – C33, P01 – P09 & H03 – H39 44
Para.
No.
NAME LCD Display Setting range Unit
Min.
Unit
Factory setting Change
During
Oper.
User
Set value
Remark
30HP/CT
40HP/VT 40HP/CT
50HP/VT
C20 JOG frequency C20 JOG Hz 0.00 to 120.00Hz Hz 0.01 5.00 N
C21 PATTERN (Mode select) C21 PATTERN 0,1,2 - - 0 N
C22 (Stage 1) C22 STAGE 1
Operation time:0.00 to 6000s
F1 to F4 and R1 to R4
s 0.01
0.00 F1
Y
C23 (Stage 2) C23 STAGE 2 0.00 F1
C24 (Stage 3) C24 STAGE 3 0.00 F1
C25 (Stage 4) C25 STAGE 4 0.00 F1
C26 (Stage 5) C26 STAGE 5 0.00 F1
C27 (Stage 6) C27 STAGE 6 0.00 F1
C28 (Stage 7) C28 STAGE 7 0.00 F1
C30 Frequency command 2 C30 FREQ CMD 2 0 to 11 - - 2 N
C31 Offset adjust (terminal [12]) C31 BIAS 12 -100.0 to +100.0% % 0.1 0.0 Y
C32 C32 GAIN 12 0.0 to +200.0% % 0.1 100.0 Y
C33 Analog setting signal filter C33 REF FILTER 0.00 to 5.00s s 0.01 0.05 Y
P Parameters
P01 Number of motor 1 poles P01 M1 POLES 2 to 14 - 2 4 N
P02
Motor 1 (Capacity) P02 M1-CAP
Up to 30[HP]: 0.01 to 60HP
HP 0.01 Motor Capacity N
40[HP] and above: 0.01 to 800HP
P03 (Rated current) P03 M1-Ir 0.00 to 2000A A 0.01 Motor rated current N
P04 (Tuning) P04 M1 TUN1 0, 1, 2 - - 0 N
P05 (On-line Tuning) P05 M1 TUN2 0, 1 - - 0 N
P06 (No-load current) P06 M1-Io 0.00 to 2000A A 0.01 Standard Rated Value N
P07 (%R1 setting) P07 M1-%R1 0.00 to 50.00% % 0.01 Standard Rated Value Y
P08 (%X setting) P08 M1-%X 0.00 to 50.00% % 0.01 Standard Rated Value Y
P09 Slip compensation control 1 P09 SLIP COMP1 0.00 to 15.00Hz Hz 0.01 0.00 Y
H Parameters
H03 Data initializing H03 DATA INIT 0, 1 - - 0 N
H04 Auto-reset (Times) H04 AUTO-RESET 0, 1 to 10 times - 1 0 Y
H05 (Reset interval) H05 RESET INT 2 to 20s s 1 5 Y
H06 Fan stop operation H06 FAN STOP 0, 1 - - 0 Y
H07 ACC/DEC pattern (Mode select) H07 ACC PTN 0,1,2,3 - - 0 N
H08 Rev. phase sequence lock H08 REV LOCK 0, 1 - - 0 N
H09 Start mode H09 START MODE 0, 1, 2 - - 0 N
H10 Energy-saving operation H10 ENERGY SAV 0, 1 - - 1 Y
H11 DEC mode H11 DEC MODE 0, 1 - - 0 Y
H12 Instantaneous OC limiting H12 INST CL 0, 1 - - 1 N
H13 Auto-restart (Restart time) H13 RESTART t 0.1 to 10.0s s 0.1 0.1 N
H14 (Freq. fall rate) H14 FALL RATE 0.00 to 100.00Hz/s Hz/s 0.01 10.00 Y
H15 (Holding DC voltage) H15 HOLD V
3ph 230V class: 200 to 300V
V 1
230V class:235V
Y
3ph 460V class: 400 to 600V 460V class:470V
H16 (OPR command selfhold time) H16 SELFHOLD t 0.0 to 30.0s, 999 s 0.1 999 N
H19 Active drive H19 AUT RED 0, 1 - - 0 Y
H20
PID control
(Mode select) H20 PID MODE 0, 1, 2 - - 0 N
H21 (Feedback signal) H21 FB SIGNAL 0, 1, 2, 3 - - 1 N
H22 (P-gain) H22 P-GAIN 0.01 to 10.00 times - 0.01 0.1 Y
H23 (I-gain) H23 I-GAIN 0.0 , 0.1 to 3600s s 0.1 0.0 Y
H24 (D-gain) H24 D-GAIN 0.00s , 0.01 to 10.0s s 0.01 0.00 Y
H25 (Feedback filter) H25 FB FILTER 0.0 to 60.0s s 0.1 0.5 Y
H26
PTC thermistor
(Mode select) H26 PTC MODE 0, 1
V 0.01
0 Y
H27 (Level) H27 PTC LEVEL 0.00 to 5.00V 1.60 Y
H30 Serial link (Function select) H30 LINK FUNC 0, 1, 2, 3 - - 0 Y
H31 (Address) H31 ADDRESS 0 (broadcast), 1 to 247 - 1 1 N
H32 (Mode select on no response error) H32 MODE ON ER 0, 1, 2, 3 - - 0 Y
H33 (Timer) H33 TIMER 0.0 to 60.0s s 0.1 2.0 Y
H34 Modbus-RTU (Baud rate) H34 BAUD RATE 0, 1, 2, 3 - - 1 Y
H35 (Data length) H35 LENGTH 0 (8-bit fixed) - - 0 Y
H36 (Parity check) H36 PARITY 0, 1, 2 - - 0 Y
H37 (Stop bits) H37 STOP BITS 0(2bit), 1(1bit) - - 0 Y
H38 (No response error detection time) H38 NO RES t 0 (No detection), 1 to 60s s 1 0 Y
H39 (Response interval) H39 INTERVAL 0.00 to 1.00s s 0.01 0.01 Y