HP Anab EQ5 - Manual (Page 48)

EQ5 AC Drive Operations Manual
_______________________________________________________________________
TECO – Westinghouse Motor Company Parameter List F00 – F42 42
5. Parameters F,E,C,P,H, A and U
This section covers parameters F,E,C,P,H, A and U which can be set via the digital operator
(see Sect. 4) to achieve a specific performance for a particular application. For most general purpose
applications, the factory settings are sufficient and will not need to be changed. If the parameter
values are to be changed, it is recommended that resulting overall drive performance be evaluated to
avoid any unwanted performance issues.
5-1 Parameters Summary List
The following tables show the setting range, LCD readout, factory setting, and whether the value can
be changed while the drive is operational.
F Parameters
Para.
No.
NAME LCD Display Setting range Unit
Min.
Unit
Factory setting Change
During
Oper.
User
Set value
Remark
30HP/CT
40HP/VT 40HP/CT
50HP/VT
F00 Data protection F00 DATA PRTC 0, 1 - - 0 N
F01 Frequency command 1 F01 FREQ CMD 1 0 to 11 - - 0 N
F02 Operation method F02 OPR METHOD 0 to 4 - - 0 N
F03 Maximum frequency 1 F03 MAX Hz-1 50 to 120Hz Hz 1 60 N
F04 Base frequency 1 F04 BASE Hz-1 25 to 120Hz Hz 1 60 N
F05 Rated voltage 1 (at Base frequency 1) F05 RATED V-1
0V: (Output voltage proportional to
V 1
230:(230V class)
460:(460V class) N
source voltage)
80 to 240V: (230V class)
320 to 480V: (460V class)
F06 Maximum voltage 1 (at Maximum frequency 1) F06 MAX V-1
80 to 240V: (230V class)
V 1
230:(230V class)
N
320 to 480V: (460V class) 460:(460V class)
F07 Acceleration time 1 F07 ACC TIME1
0.01 to 3600s s 0.01 6.0 20.0 Y
F08 Deceleration time 1 F08 DEC TIME1
F09 Torque boost 1 F09 TRQ BOOST1 0.0, 0.1 to 20.0 - 0.1 0.1 Y
F10 Electronic (Select) F10 ELCTRN OL1 0, 1, 2 - - 1 Y
F11 thermal 1( Level) F11 OL LEVEL1 INV rated current 20 to 135% A 0.01 Motor rated current Y
F12 (Thermal time constant) F12 TIME CNST1 0.5 to 75.0 min min 0.1 5.0 10.0 N
F13
Electronic thermal overload relay
(for braking resistor)
F13 DBR OL
[Up to 10HP/CT, 15HP/VT]
- -
0
Y
0, 2
[15HP/CT, 20HP/VT and above ]
0
0
F14 Restart mode after momentary power failure F14 RESTART 0 to 5 - - 0 N
F15 Frequency limiter (High) F15 H LIMITER
0-120Hz Hz 1 70
Y
F16 (Low) F16 L LIMITER N
F17 Gain (for freq. set signal) F17 FREQ GAIN 0.0 to 200.0% % 0.1 100.0 Y
F18 Bias frequency F18 FREQ BIAS -120.0 to +120.0Hz Hz 0.1 0.0 Y
F20 DC brake (Starting freq.) F20 DC BRK Hz 0.0 to 60.0Hz Hz 0.1 0.0
Y F21 (Braking level) F21 DC BRK LVL 0 to 100% % 1 0
F22 (Braking time) F22 DC BRK t 0.0s (Inactive) s 0.1 0.0
F23 Starting frequency (Freq.) F23 START Hz 0.1 to 60.0Hz Hz 0.1 0.5
N
F24 (Holding time) F24 HOLDING t 0.0 to 10.0s s 0.1 0.0
F25 Stop frequency F25 STOP Hz 0.1 to 60.0Hz Hz 0.1 0.2 N
F26 Motor sound (Carrier freq.) F26 MTR SOUND 0.75 to 15kHz (Vary by HP) kHz 1 2
Y
F27 (Sound tone) F27 SOUND TONE 0 to 3 - - 0
F30 FMA (Voltage adjust) F30 FMA V-ADJ 0 to 200% % 1 100
Y
F31 (Function) F31 FMA FUNC 0 to 11 - - 0
F33 FMP (Pulse rate) F33 FMP PULSES 300 to 6000p/s (full scale) p/s 1 1440
Y F34 (Voltage adjust) F34 FMP V-ADJ 0%, 1 to 200% % 1 0
F35 (Function) F35 FMP FUNC 0 to 10 - - 0
F36 30RY operation mode F36 30RY MODE 0, 1 - - 0 Y
F40 Torque limiter 1 (Driving) F40 DRV TRQ 1 20 to 150%, 999 % 1 999
Y
F41 (Braking) F41 BRK TRQ 1 0%, 20 to 150%, 999 999
F42 Torque vector control 1 F42 TRQVECTOR1 0, 1 - - 0 N