HEIDENHAIN MANUALplus 4110 Pilot User Manual
Page 37

36
Milling cycles
Face milling
Depending on the parameters, the cycle mills on the end face:
• One or two surfaces (Q=1 or Q=2, B>0)
• One rectangle (Q=4, L<>B)
• One square (Q=4, L=B)
• One triangle or polygon (Q=3 or Q>4, L>0)
• One circle (Q=0, RE>0, L and B: no entry)
For one or two surfaces, “B“ defines the remaining thickness (the
material which remains). For an even number of surfaces you can
program “B“ instead of “V“.
Information on the cycle parameters:
B:
Width across flats
• When Q=1, Q=2: B is the remaining thickness
• Rectangle: Rectangle width
• Square, polygon (Q
4): B is the width across flats
• Circle: no entry
A:
Angle to the X axis – default: 0
• Polygon (Q>2): Position of the figure
• Circle: no entry
H:
Cutting direction – default: 0
• H=0: Up-cut milling
• H=1: Down-cut milling
J:
Uni-/bidirectional
• J=0: Unidirectional
• J=1: Bidirectional
O:
Roughing/finishing – default: 0
• O=0: Roughing
• O=1: Finishing
- TNC 122 User Manual (63 pages)
- TNC 122 Technical Manual (70 pages)
- TNC 360 Service Manual (157 pages)
- TNC 416 Technical Manual (510 pages)
- TNC 335 Technical Manual (581 pages)
- TNC 360 User Manual (237 pages)
- TNC 360 ISO-Programmierung (2 pages)
- TNC 415 (280 540) User Manual (227 pages)
- TNC 370D (92 pages)
- TNC 416 (289 pages)
- TNC 415 (280 540) Technical Manual (752 pages)
- TNC 415 (259 96x) Service Manual (195 pages)
- TNC 407 (280 580) User Manual (376 pages)
- iTNC 530 (340 420) Pilot (104 pages)
- TNC 407 (280 580) ISO Programming (333 pages)
- TNC 415 (280 540) Service Manual (252 pages)
- PT 880 Installation (112 pages)
- ND 100 User Manual (116 pages)
- ND 287 User Manual (147 pages)
- ND 280 Quick Start (12 pages)
- ND 200 (156 pages)
- ND 282 (10 pages)
- ND 287 Quick Start (26 pages)
- ND 282 B (39 pages)
- ND 281 A (44 pages)
- ND 281 B v.1 (53 pages)
- ND 281 B v.2 (65 pages)
- ND 221 v.2 (10 pages)
- ND 231 B v.2 (56 pages)
- ND 231 B v.1 (44 pages)
- ND 221 B v.2 (45 pages)
- ND 550 v.2 (8 pages)
- NDP 560 (10 pages)
- ND 523 (93 pages)
- ND 570 (8 pages)
- ND 750 v.2 (46 pages)
- ND 760 v.3 (72 pages)
- ND 770 v.1 (40 pages)
- ND 770 v.3 (41 pages)
- ND 760 E (44 pages)
- IOB 49 (21 pages)
- NDP 960 (68 pages)
- ND 780 Installation (132 pages)
- ND 970 (47 pages)
- ND 1100 Quick Start (36 pages)