Altera RapidIO II MegaCore Function - Manual (Page 149)

Chapter 6: Software Interface 6–11
Physical Layer Registers
August 2014 Altera Corporation RapidIO II MegaCore Function
User Guide
1.25_GB_ENABLE [24] RW
Indicates whether port operation at 1.25 Gbaud is enabled in the
RapidIO implementation.
1’b0: The IP core cannot support 1.25 Gbaud operation.
1’b1: The IP core can support 1.25 Gbaud operation. This field can
only have this value if 1.25_GB_SUPPORT has the value of 1
1'b1
2.5_GB_SUPPORT [23] RO
Indicates whether the RapidIO II IP core supports port operation at
2.5 Gbaud.
1’b0: The IP core does not support 2.5 Gbaud operation.
1’b1: The IP core supports 2.5 Gbaud operation.
1'b1
2.5_GB_ENABLE [22] RW
Indicates whether port operation at 2.5 Gbaud is enabled in the RapidIO
implementation.
1’b0: The IP core cannot support 2.5 Gbaud operation.
1’b1: The IP core can support 2.5 Gbaud operation. This field can
only have this value if 2.5_GB_SUPPORT has the value of 1
1'b1
3.125_GB_SUPPORT [21] RO
Indicates whether the RapidIO II IP core supports port operation at
3.125 Gbaud.
1’b0: The IP core does not support 3.125 Gbaud operation.
1’b1: The IP core supports 3.125 Gbaud operation.
1'b1
3.125_GB_ENABLE [20] RW
Indicates whether port operation at 3.125 Gbaud is enabled in the
RapidIO implementation.
1’b0: The IP core cannot support 3.125 Gbaud operation.
1’b1: The IP core can support 3.125 Gbaud operation. This field can
only have this value if 3.125_GB_SUPPORT has the value of 1
1'b1
5.0_GB_SUPPORT [19] RO
Indicates whether the RapidIO II IP core supports port operation at
5.0 Gbaud.
1’b0: The IP core does not support 5.0 Gbaud operation.
1’b1: The IP core supports 5.0 Gbaud operation.
1'b1
5.0_GB_ENABLE [18] RW
Indicates whether port operation at 5.0 Gbaud is enabled in the RapidIO
implementation.
1’b0: The IP core cannot support 5.0 Gbaud operation.
1’b1: The IP core can support 5.0 Gbaud operation. This field can
only have this value if 5.0_GB_SUPPORT has the value of 1
1'b1
6.25_GB_SUPPORT [17] RO
Indicates whether the RapidIO II IP core supports port operation at
6.25 Gbaud.
1’b0: The IP core does not support 6.25 Gbaud operation.
1’b1: The IP core supports 6.25 Gbaud operation.
1'b1
6.25_GB_ENABLE [16] RW
Indicates whether port operation at 6.25 Gbaud is enabled in the
RapidIO implementation.
1’b0: The IP core cannot support 6.25 Gbaud operation.
1’b1: The IP core can support 6.25 Gbaud operation. This field can
only have this value if 6.25_GB_SUPPORT has the value of 1.
1'b1
RSRV [15:4] RO Reserved 12'b0
Table 6–13. Port 0 Control 2 CSR—Offset: 0x154 (1) (Part 2 of 3)
Field Bits Access Function Default