Lenze EVS9332xS - Manual (Page 254)

Configuration
Code table
8
8.4
l
8.4−13 EDSVS9332S EN 6.0−07/2013
IMPORTANT Possible settings Code
Selection Lenze Designation No.
C0264 MPOT1
ON/OFF
0 0
1
2
3
4
5 No change
Deceleration with T
if
to 0%
Deceleration with T
if
to C0261
Skip with T
if
= 0 to 0%
Skip with T
if
= 0 to C0261
Acceleration with T
ir
to C0260
MPOT1
Executable functions if motor potentiometer
is deactivated via input MPOT1−INACTIVE.
C0265 MPOT1 INIT 0 0
1
2 Value during mains failure
Lower limit value from C0261
0 % MPOT1
Initialisation
Value which is accepted during mains
switching and activated motor pot.
C0267
s
® Selection list 2 MPOT1
Configuration of digital input signals
1 UP 1000 FIXED0
2 DOWN 1000 FIXED0
C0268
s
MPOT1−INACT 1000 FIXED0 ® Selection list 2 MPOT1
Configuraton of digital input signal
C0269 g
1 (C0267/1)
2 (C0267/2)
3 (C0268)
C0291 SSC OVERRIDE 0 0 {1 rpm} 16000 SSC cutout frequency
Cutout frequency for the transition from
sensorless control to controlled operation
C0292 SSC IM SET 0.00 0.00 {0.01 A} 500.00 SSC Im setpoint
Motor current setpoint.
For sensorless control, set 1.0 ... 1.1−fold rated
motor current.
C0293 SSC DYNAMIC 0.00 0.00 {0.01 %} 199.00 SSC dynamic constant
C0294 VP FRQ CTRL ® 0.0 {0.1} 99.9 Vp frequency controller
Proportional gain of frequency controller
à Depending on C0086
C0295 TN FRQ CTRL ® 2 {1 ms} 20000 Tn frequency controller
Adjustment time frequency controller
à Depending on C0086
C0296 DYNAMIC
CONST
100 0 {0.1} 32767 Dynamic constant
C0325 VP2 ADAPT 1.0 0.1 {0.1} 500.0 PCTRL Adpation Vp2
Process controller adaptation gain (V
p2
)
C0326 VP3 ADAPT 1.0 0.1 {0.1} 500.0 PCTRL adaptation Vp3
Process controller adaptation gain (V
p3
)
C0327 SET2 ADAPT 100.0
0
0.00 {0.01 %} 100.00 PCTRL adaptation nset2
Set speed threshold of the process controller
adaptation (condition: C0327 > C0328)
C0328 SET1 ADAPT 0.00 0.00 {0.01 %} 100.00 PCTRL adaptation nset1
Set speed threshold of the process controller
adaptation (condition: C0328 < C0327)
C0329 ADAPT ON/OFF 0 0
1
2
3 No process controller adaptation
External via input
Adaptation via setpoint
Adaptation via control difference PCTRL Adaptation on/off
Activate process controller adaptation
C0332 PCTRL TIR 0.000 0.000 {0.001 s} 999.900 PCTRL
Acceleration time T
ir
(relating to setpoint change 0...100 %)
C0333 PCTRL TIF 0.000 0.000 {0.001 s} 999.900 PCTRL
Deceleration time T
if
(based on setpoint change 0...100 %)