Extron Electronics HDXP Plus Series User Guide User Manual
Page 69
HDXP Plus Series Switchers • Remote Configuration and Control
63
Command
ASCII Command
(Host to Switcher)
Response
(Switcher to Host)
Additional Description
IP Setup Commands (continued)
Set DHCP on or off
E
X4%
DH
}
Idh
X4%
]
Set DHCP on or off (
X4%
).
Read DHCP status
E
DH
}
X4%
]
View DHCP status
X4%
.
Set IP address
E
CI
X2&
CI
}
Ipi
X2&
]
Set IP address
X2&
.
Read IP address
E
CI
}
X2&
]
View the HDXP IP address.
Read hardware (MAC)
address
E
CH
}
X3$
]
View media access code
(MAC) address
X3$
for your
unit.
Set subnet mask
E
X5*
CS
}
Ips
X5*
]
Set subnet mask
X5*
for the
HDXP.
Read subnet mask
E
CS
}
X5*
]
View the subnet mask.
Set gateway IP address
E
X5(
CG
}
Ipg
X5(
]
Set gateway IP address
X5(
for the HDXP.
Read gateway IP address
E
CG
}
X5(
]
View the gateway address.
Set administrator password
E
X3)
CA
}
Ipa •
X3)
]
Set administrator password
X3)
for the HDXP.
Read administrator password
E
CA
}
X3)
]
View current administrator
password.
Reset (clear) administrator
password
E
• CA
}
Ipa •
]
Remove all administrator and
user passwords.
Set user password
E
X3)
CU
}
Ipu •
X3)
]
Set user password
X3)
for the
HDXP.
NOTE: An administrator password must be in place before a user password can be set.
Read user password
E
CU
}
X3)
]
View the user password.
Reset (clear) user password
E
• CU
}
Ipu •
]
Clear the user password only.
Bidirectional Serial Port Commands
Configure port parameters
24
E
X4^
*
X4&
X4*
,
X4(
,
X5)
CP
}
Cpn
X4^
• Ccp
X4&
,
X4*
,
X4(
,
X5)
]
Set baud rate
X4&
, parity
X4*
,
Data bits
X4(
, and stop bits
X5)
for the IP connection for
port
X4^
.
Read port parameters
E
X4^
CP
}
X4&
,
X4*
,
X4(
,
X5)
]
View the parameters of port
X4^
.
Set serial port mode
E
X4^
*
X5!
CY
}
Cpn
X4^
• Cty
X5!
]
Set the serial communication
type
X5!
for serial port
X4^
.
Read serial port mode
E
X4^
CY
}
X5!
]
View mode
X5!
of port
X4^
.
NOTE:
X2&
= IP address
Format nnn.nnn.nnn.nnn. Leading zeros in each field are optional.
X3)
= Password
Administrator or user password can be 4 to 12 alphanumeric
characters. Spaces and special characters or symbols are not
allowed. The password is case-sensitive.
X3$
= MAC address
Format nn-nn-nn-nn-nn-nn.
X4%
= DHCP status
0 = off, 1 = on. Default is 0.
X4^
= Serial port number
01 = RS232/RS422 port on rear panel, 02 = front panel Config port
X4&
= Baud rate
9600, 19200, 384000, or 115200
X4*
= Parity
odd, even, none, mark, or space (only first letter required)
X4(
= Data bits
1 or 2
X5)
= Stop bits
7 or 8
X5!
= Serial port type
0 = RS-232, 1 = RS-422
X5*
= Subnet mask
Format nnn.nnn.nnn.nnn. Leading zeros in each field are optional.
X5(
= Gateway IP address
Format nnn.nnn.nnn.nnn. Leading zeros in each field are optional.