Texas Instruments TMS320C2XX User Manual
Page 361
Timer
8-11
On-Chip Peripherals
Figure 8–5. ’C2xx Timer Control Register (TCR) — I/O-Space Address FFF8h
15
12
11
10
9
6
5
4
3
0
ЙЙЙЙЙЙЙЙ
ЙЙЙЙЙЙЙЙ
Reserved
FREE
SOFT
PSC
TRB
TSS
TDDR
0
R/W–0
R/W–0
R/W–0
R/W–0
W–0
R/W–0
Note:
0 = Always read as zeros; R = Read access; W = Write access; value following dash (–) is value after reset.
Bits 15–12
Reserved. Bits 15–12 are reserved and are always read as 0s.
Bits 11–10
FREE, SOFT — These bits are special emulation bits that determine the
state of the timer when a breakpoint is encountered in the high-level lan-
guage debugger. If the FREE bit is set to 1, then, upon a software breakpoint,
the timer continues to run (that is, free runs). In this case, SOFT is a
don’t
care. But if FREE is 0, then SOFT takes effect. In this case, if SOFT = 0, the
timer halts the next time the TIM decrements. If the SOFT bit is 1, then the
timer halts when the TIM has decremented to zero. Table 8–3 summarizes
the available run and emulation modes. The default (reset) setting is
FREE = 0 and SOFT = 0.
Table 8–3. ’C2xx Timer Run/Emulation Modes
ББББ
ББББ
FREE
ББББ
ББББ
SOFT
БББББББББББББББББ
БББББББББББББББББ
Timer Run/Emulation Mode
ББББ
ББББ
0
ББББ
ББББ
0
БББББББББББББББББ
БББББББББББББББББ
Stop after the next decrement of the TIM (hard stop)
ББББ
Б
ББ
Б
ББББ
0
ББББ
Б
ББ
Б
ББББ
1
БББББББББББББББББ
Б
БББББББББББББББ
Б
БББББББББББББББББ
Stop after the TIM decrements to 0 (soft stop)
ББББ
ББББ
1
ББББ
ББББ
0
БББББББББББББББББ
БББББББББББББББББ
Free run
ББББ
ББББ
1
ББББ
ББББ
1
БББББББББББББББББ
БББББББББББББББББ
Free run
Bits 9–6
PSC — Timer prescaler counter. These four bits hold the current prescale
count for the timer. For every CLKOUT1 cycle that the PSC value is greater
than 0, the PSC decrements by one. One CLKOUT1 cycle after the PSC
reaches 0, the PSC is loaded with the contents of the TDDR, and the timer
counter register (TIM) decrements by one. The PSC is also reloaded when-
ever the timer reload bit (TRB) is set by software. The PSC can be checked
by reading the TCR, but it cannot be set directly. It must get its value from
the timer divide-down register (TDDR). At reset, the PSC is set to 0.
Bit 5
TRB — Timer reload bit. When you write a 1 to TRB, the TIM is loaded with
the value in the PRD, and the PSC is loaded with the value in the timer divide-
down register (TDDR). The TRB bit is always read as zero.