beautypg.com

Maxim Integrated 71M6513H Power Meter IC Family Software User Manual

Page 71

background image

71M651x Software User’s Guide

XRAM

Word

Address

Default

Value

Name

Description

0x02

191181742

(6511)

136105056

(6513)

PK_VTHR

Demo Code revision 3.04: Not implemented.
Demo Code revision 3.05: When the voltage exceeds this value, bit 5
in the MPU status word is set, and the MPU might choose to log a
warning. Event logs are not implemented in Demo Code.
6511: LSB = 6.6952*10

-13

*VMAX

2

V

2

h

RMS

6513: LSB = 9.4045*10

-13

*VMAX

2

V

2

h

RMS

The default value is equivalent to 407.3V

RMS

if VMAX = 600V and a 1-

second accumulation interval is used.

0x03

24856631

(6511)

17695797

(6513)

PK_ITHR

Demo Code revision 3.04: Not implemented.
Demo Code revision 3.05: When the current exceeds this value, bit 6
in the MPU status word is set, and the MPU might choose to log a
warning. Event logs are not implemented in Demo Code.
6511: LSB = 6.6952*10

-13

*IMAX

2

V

2

h

RMS

6513: LSB = 9.4045*10

-13

*VMAX

2

V

2

h

RMS

The default value is equivalent to 50.9A

RMS

if IMAX = 208A and a 1-

second accumulation interval is used.

0x04

0

Y_CAL

0x05

0

Y_CALC

0x06

0

Y_CALC2

Implement RTC trim.

1000

2

_

100

_

10

_

)

(

2

CALC

Y

T

CALC

Y

T

CAL

Y

ppm

CORRECTION

+

+

=

0x09

6000

VMAX

The nominal external RMS voltage that corresponds to 250mV pk at the
ADC input. The meter uses this value to convert internal quantities to
external. LSB=0.1V

0x0A

2080

IMAX

The nominal external RMS current that corresponds to 250mv pk at the
ADC input. The meter uses this value to convert internal quantities to
external. LSB=0.1A

0x0B

0

PPMC

PPM/C*26.84. Linear temperature compensation. A positive value will
cause the meter to run faster when hot. This is applied to both V and I
and will therefore have a double effect on products.

0x0C

0

PPMC2

PPM/C

2

*1374. Square-law compensation. A positive value will cause

the meter to run faster when hot. This is applied to both V and I and will
therefore have a double effect on products.

0x0D

9585

(6511)

22721

(6513)

DEGSCALE

Scale factor for TEMP_X.
TEMP_X=DEGSCALE*2

-22

*(TEMP_RAW_X - TEMP_NOM)

0x13

61

(6511)

16

(6513)

ICREEP

For each element, if the current of that element is below ICREEP, the
sample values for that element are zeroed. In that case, the accumula-
tors for Wh, VARh, and VAh are not updated and the instantaneous
value of IRMS for that element is zeroed. The default values correspond
to 80mA, if the default setting for IMAX is used.
6511: LSB = 6.6952*10

-13

IMAX

2

Wh

6513: LSB = 9.4045*10

-13

IMAX

2

Wh

Table 5-3: MPU Input Parameters

Revision 2.4

TERIDIAN Proprietary

71 of 137

© Copyright 2005-2006 TERIDIAN Semiconductor Corporation