MacDon M100 SP Operators Manual - Manual (Page 45)

OPERATOR’S STATION
169304
43
Rev. C
L1 C x x x || R E A D S E N S O R I N P U T S ?
L2 M x x x || N O / Y E S A C T I V A T E F U N C T I O N S ?
L1 C x x x || S E N S O R I N P U T
L2 M x x x || H D R H E I G H T 3 . 5 9 V
L1 C x x x || S E N S O R I N P U T
L2 M x x x || H E A D E R A N G L E 1 . 8 4 V
L1 C x x x || S E N S O R I N P U T
L2 M x x x || K N I F E S P E E D 1 2 3 H Z
L1 C x x x || S E N S O R I N P U T
L2 M x x x || R E E L S P E E D 1 2 3 H Z
L1 C x x x || S E N S O R I N P U T
L2 M x x x || W H E E L S P E E D 1 2 3 H Z
L1 C x x x || E X I T R E A D S E N S O R S ?
L2 M x x x || N O / Y E S S E N S O R I N P U T
H D R
H E I G H T 3 . 5 9 V
L1 C x x x || S E N S O R I N P U T
L2 M x x x || H D R H E I G H T S E N S O R
L1 C x x x || S E N S O R I N P U T
L2 M x x x || H E A D E R A N G L E S E N S O R
L1 C x x x || S E N S O R I N P U T
L2 M x x x || K N I F E S P E E D S E N S O R
L1 C x x x || S E N S O R I N P U T
L2 M x x x || R E E L S P E E D S E N S O R
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || N O / Y E S E X I T D I A G N O S T I C S ?
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || H E A D E R D O W N / U P
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || R E E L D O W N / U P
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || H D R T I L T I N / O U T
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || K N I F E D R I V E O N
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || D R A P E R / A U G E R O N
L1 C x x x || A C T I V A T E F U N C T I O N S ?
L2 M x x x || R E E L F O R E / A F T
L1 C x x x || A C T I V A T E H Y D P U R G E ?
L2 M x x x || N O / Y E S
L1 C x x x || T O A C T I V A T E P U R G E
L2 M x x x || P R E S S A N D H O L D
L1 C x x x || P U R G E C Y C L E S T A R T E D
L2 M x x x || P R E S S A N D H O L D
L1 C x x x || P U R G E C Y C L E E N D E D
L2 M x x x ||
L1 C x x x || P U R G E C Y C L E E N D E D
L2 M x x x || N O E X I T Y E S
L1 C x x x || E X I T F U N C T I O N M E N U ?
L2 M x x x || N O / Y E S H E A D E R D O W N / U P
L1 C x x x || E X I T D I A G N O S T I C S ?
L2 M x x x || N O / Y E S D I A G N O S T I C M O D E ?
If "NO" then jump to:
If "NO" then jump to:
ACTIVATE HYD PURGE - This is to allow the
operator to purge the air from a new or changed pump
system.
Pressing and holding the right hand "arrow" button
activates a predetermined timed purge cycle.
Releasing pressure on the switch or a completed
cycle (timed out) will jump to the PURGE CYCLE
ENDED menu selection.
If the HEADER TILT cylinder or the REEL FORE /
AFT valve is not installed under the TRACTOR
SETUP menu then the ACTIVATE FUNCTIONS menu
selection for these items should be suppressed.
If no expansion module or an A30 auger header is
selected, the corresponding menu items should be
suppressed.
For diagnostic purposes each header function can be
activated by using the "arrow" keys on the CDM.
When "SELECT" is pressed the program will go to the
next function that can be activated.
If "NO" then jump to:
If a sensor has been disabled "SENSOR" will be
flashing in the area where the input reading would
have been.
When "SELECT" is pressed the program goes to the
EXIT READ SENSORS? menu selection.
For diagnostic purposes each sensors input signal can
be read.
If no expansion module or an A30 auger header is
selected, the corresponding menu items should be
suppressed.
If "NO" then jump to:
Adds a selection to be able to read in the wheel speed
frequency.
If "NO" then jump to: