MacDon M205 Quick Card - Manual

BREAK-IN INSPECTIONS
HRS ITEM CHECK
1 Drive Wheel Nuts
Torque: 375 ft∙lbf (510 N·m) dry
Refer to M205 Operator’s Manual
5
A/C Belt Tension
Caster Wheel Nuts Torque: 120 ft·lbf (163 N·m)
Caster Wheel
Anti-Shimmy
Dampener Bolts
Torque Inboard: 100 ft∙lbf (135 N·m)
Torque Outboard: 85 ft∙lbf (115 N·m)
Walking Beam Bolts Torque: 330 ft∙lbf (448 N·m)
10
Walking Beam Bolts Torque: 330 ft∙lbf (448 N·m)
Neutral Dealer Adjust
50
Hose Clamps:
Air Intake, Radiator,
Heater, Hydraulic
Tightness
Walking Beam Bolts Torque: 330 ft∙lbf (448 N·m)
Caster Wheel
Anti-Shimmy
Dampener Bolts
Torque Inboard: 100 ft∙lbf (135 N·m)
Torque Outboard: 85 ft∙lbf (115 N·m)
Engine Gearbox Oil
Change
Drive Wheel Oil
Hydraulic Oil Filters
(except lift)
ONGOING MAINTENANCE INTERVALS
TIME SERVICE
10 Hours
or Daily
1. Check tire inflation.
2. Check engine oil and engine coolant levels.
3. Clean radiator and hydraulic oil cooler, and
charge air cooler and A/C condenser.
4. Check hydraulic oil level, hoses and lines for leaks.
5. Drain fuel filter water trap.
50 Hours
1. Grease caster pivots and spindle bearings.
2. Grease top link pivots.
3.Clean cab fresh air intake filter.
4. Check engine gearbox/drive wheel lubricant.
100 Hours
or
Annually
1. Clean cab air return filter.
NOTE: Refer to M205 Operator’s Manual for
250, 500, 1000, 1500, 2000 hour and annual maintenance.
FLUIDS AND LUBRICANTS
FLUID VOL SPEC
DESCRIPTION /
INFORMATION
Fuel:
Diesel No.2
97 US
Gallons
(378 L)
ATSM
D-975
Refer to M205
Operator’s Manual
Fuel:
Diesel No.1
and No. 2
Mix
97 US
Gallons
(378 L)
n/a
Refer to M205
Operator’s Manual
Antifreeze
8.2 US
Gallons
(31L)
ASTM
D-4985
Refer to M205
Operator’s Manual
Grease N/A
SAE Multi-
Purpose
High Temp. Extreme
Pressure EP2.
Max 1%
molybdenum
disulphide,
Lithium base.
Use as required
unless otherwise
noted.
Engine Oil
15 US
Quarts
(14.2 L)
Engine Crankcase
SAE 15W40
for API Class
SJ and CH-4
Hydraulic
Oil
17.2 US
Gallons
(66 L)
Windrower and
Header Drive
Gear Lube
2.2 US
Quarts
(2.1L)
SAE 75W-90
API
Service
Class GL-5.
E Synthetic
Trans Lube
Engine Gearbox
1.5 US
Quarts
(1.4 L)
Power Wheels
A/C
Refrigerant
5 lb
(2.27 kg)
R134A - - -
Compressor
Oil
8.1 fl. oz
(240 cc)
PAG SP-15 - - -
TIRE PRESSURES
Bar 32 psi (2.2 bar)
Turf 20 psi (1.4 bar)
Caster Wheels 10 psi (0.7 bar)
A-Series, R-Series, or D-Series without
Hydraulic Deck Shift
FLOAT PRESET/DECK SHIFT switch allows
for auto-memory of three different trim cylinder
positions. For example:
#1 - Border Width LH 5.0, RH 6.5
#2 - Normal Width LH 5.0, RH 5.0
#3 - Rocky Width LH 6.5, RH 6.5
D-Series with Hydraulic Deck Shift
DECK SHIFT switch activates hydraulic deck
shifting when header is engaged, and allows for
auto-memory of trim cylinder adjustments in
each delivery opening position.
Allows for compensation of weight shifts to the
float springs.
FLOAT PRESETS
1. Place GSL in N-DETENT.
2. Set throttle to start position - fully back.
3. Sound horn three times.
4. Turn ignition key to RUN position.
Single loud tone sounds, engine warning lights illuminate, and
CDM displays HDR DISENGAGED or HEADER ENGAGED and
IN PARK.
5. Turn ignition key to START position until engine starts, and then
release key. Tone ceases and warning lights go out.
CDM displays the programmed header data for five seconds
(if attached) and then returns to previous display.
NORMAL START
M205 Windrower Quick Card - Form 169889 Rev. A
Supplement to M205 Windrower Operator’s Manual - Form 169887
M205 Windrower Quick Card - Form 169889 Rev. A
Supplement to M205 Windrower Operator’s Manual - Form 169887