Allied Telesis AT-8202 Instruction Manuals and User Guides
We have 2 Instruction Manuals and User Guides for AT-8202 Allied Telesis
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 30 |
| Size: | 383 KB |
Show table of contents
Document Outline
- AT8202 AT-8203
- Electrical Safety and Installation Requirements
- Uplink Card Installation
- Who Should Use This Guide
- About the ATM Uplink Card
- About the FDDI Uplink Card
- Verifying Your Uplink Package
- Prerequisites for Card Installation
- Installing the Uplink Card
- 1. Turn off power to the FORMULA8200.
- 2. Unplug the unit.
- 3. Disconnect and label all connections to the swi...
- 4. Remove additional hardware, such as rackmountin...
- 5. Remove the top cover from the unit, as follows:...
- 6. Using a #1 Phillips screwdriver, remove the scr...
- 7. Install the uplink card into the lower PCI slot...
- 8. Using the screw from Step6, secure the uplink ...
- 9. Proceed immediately to the next sections to ins...
- Installing the Accelerator Card
- Replacing the Chassis Top Cover
- Initializing the Switch
- Interpreting the LEDs
- Cabling Requirements for the FDDI Uplink Card
- Where to Go From Here
- In Case of Problems
- Product Specifications for the FORMULA8200 Switch...
- Technical Support Fax Order
- FORMULA 8200 Uplink Card Installation Guide Feedba...
- Lindfield, NSW
- Rexdale, Ontario
- Richmond,BritishColumbia
- Abingdon, Oxon
- Les Ulis
- Berlin
- Freising
- Mongkok
- Milano
- Machida-shi,Tokyo
- Yodogawa-ku,Osaka
- Scottsdale, AZ
- LosAngeles,CA
- Mission Viejo, CA
- SanDiego,CA
- Santa Ana, CA
- Clearwater,FL
- Norcross,GA
- Reading,MA
- Eden Prairie, MN
- St. Louis, MO
- Dover, NH
- Plaistow, NH
- Portsmouth, NH
- Morrisville, NC
- Lake Oswego, OR
- Austin,TX
- Dallas,TX
- San Antonio, TX
- Vienna,VA
| Recognized languages: | English |
|---|---|
| Pages: | 80 |
| Size: | 564 KB |
Show table of contents
Document Outline
- user’s GUIDE
- Preface
- Features
- Configuring the ATM Port
- Configuring Classical IP Over ATM (CIP)
- When using CIP, make sure that the ATM port is con...
- 1. Create a VLAN with a valid IP address, using th...
- 2. Create a CIP service.
- 3. Set the connection type.
- 4. Set the following values:
- 5. Define an IP address and subnet mask for this C...
- 6. Save the CIP configuration
- To configure CIP services:
- Figure1-2 Configuring CIP
- To connect two switches for CIP service, you must ...
- When using CIP, make sure that the ATM port is con...
- Configuring the LAN Emulation Client (LEC)
- Configuring Point-to-Point (PTOP)
- Configuring Trunking
- Where to Go Next
- Chapter2
- ATM Commands
- How Commands are Organized
- Entering Commands
- Command Edit Mode
- ATM Command Descriptions
- ATM/CONFIG/CREATE Commands
- ATM/CONFIG/DELETE Commands
- ATM/CONFIG/DISABLE and ENABLE Commands
- ATM/CONFIG/MODIFY Commands
- ATM/SHOW Commands
- CIP 5 ARP Table Display
- Table2-7 ATM/SHOW/ARP/CIP Parameters
- Table2-8 ATM/SHOW/ARP/LEC Parameters
- Table2-9 ATM/SHOW/CIP Parameters
- Table2-10 ATM/SHOW/CIP
Parameters - Table2-11 ATM/SHOW/CONNECTION Parameters
- Table2-12 ATM/SHOW/CONNECTION
Parameters... - Table2-13 ATM/SHOW/LEC
Parameters ... - Table2-14 ATM/SHOW/PORT Parameters
- Table2-15 ATM/SHOW/PTOP Parameters
- Table2-16 ATM/SHOW/TRUNK Parameters
- ATM/STATS Commands
- ATM/TEST Command
- AppendixA
- Index