HEIDENHAIN TNC 320 (340 551-01) - Manual (Page 114)

114 –˜pV"hhamV9˜pV"hhamV˜ pm›p¤’
6.1 T
ool Mo
v
e
ments
6.1 Tool Movements
Path functions
˜§pczaF4F˜4pm›p¤˜a’˜¤’¤"dd©˜4phzp’F=˜pO˜’F¦F"d˜4pm›p¤˜
FdFhFm›’:˜’¤4^˜"’˜’›"aV^›˜damF’˜"m=˜4a4¤d"˜"4’˜a›^˜›^F˜z"›^˜
O¤m4›apm’:˜©p¤˜4"m˜zpV"h˜›^F˜›ppd˜hp¦FhFm›’˜Op˜straight lines˜"m=˜
circular arcs.
FK Free Contour Programming
O˜"˜zp=¤4›apm˜="§amV˜a’˜mp›˜=ahFm’apmF=˜Op˜ ˜"m=˜›^F˜=ahFm’apm’˜
Va¦Fm˜"F˜mp›˜’¤OOa4aFm›˜Op˜4F"›amV˜"˜z"›˜zpV"h:˜©p¤˜4"m˜zpV"h˜
›^F˜§pczaF4F˜4pm›p¤˜§a›^˜›^F˜ ˜OFF˜4pm›p¤˜zpV"hhamV˜"m=˜
^"¦F˜›^F˜ ˜4"d4¤d"›F˜›^F˜ha’’amV˜="›"
a›^˜ ˜zpV"hhamV:˜©p¤˜"d’p˜zpV"h˜›ppd˜hp¦FhFm›’˜Op˜straight
lines
˜"m=˜circular arcs
Miscellaneous functions M
a›^˜›^F˜ Œ’˜ha’4Fdd"mFp¤’˜O¤m4›apm’˜©p¤˜4"m˜"OOF4›
„ pV"h˜¤m:˜FV:˜"˜zpV"h˜am›F¤z›apm
„ "4^amF˜O¤m4›apm’:˜’¤4^˜"’˜’§a›4^amV˜’zam=dF˜p›"›apm˜"m=˜4ppd"m›˜
’¤zzd©˜pm˜"m=˜pOO
„ pm›p¤amV˜*F^"¦ap˜pO˜›^F˜›ppd
Subprograms and program section repeats
O˜"˜h"4^amamV˜’F„¤Fm4F˜p44¤’˜’F¦F"d˜›ahF’˜am˜"˜zpV"h:˜©p¤˜4"m˜
’"¦F˜›ahF˜"m=˜F=¤4F˜›^F˜4^"m4F˜pO˜zpV"hhamV˜Fp’˜*©˜Fm›FamV˜
›^F˜’F„¤Fm4F˜pm4F˜"m=˜›^Fm˜=FOamamV˜a›˜"’˜"˜’¤*zpV"h˜p˜zpV"h˜
’F4›apm˜FzF"›˜O˜©p¤˜§a’^˜›p˜F¨F4¤›F˜"˜’zF4aOa4˜zpV"h˜’F4›apm˜pmd©˜
¤m=F˜4F›"am˜4pm=a›apm’:˜©p¤˜"d’p˜=FOamF˜›^a’˜h"4^amamV˜’F„¤Fm4F˜"’˜
"˜’¤*zpV"h˜m˜"==a›apm:˜©p¤˜4"m˜^"¦F˜"˜z"›˜zpV"h˜4"dd˜"˜’Fz""›F˜
zpV"h˜Op˜F¨F4¤›apm
pV"hhamV˜§a›^˜’¤*zpV"h’˜"m=˜zpV"h˜’F4›apm˜FzF"›’˜a’˜
=F’4a*F=˜am˜ ^"z›F˜n
Programming with Q parameters
m’›F"=˜pO˜zpV"hhamV˜m¤hFa4"d˜¦"d¤F’˜am˜"˜z"›˜zpV"h:˜©p¤˜Fm›F˜
h"cF’˜4"ddF=˜˜z""hF›F’˜ p¤˜"’’aVm˜›^F˜¦"d¤F’˜›p˜›^F˜
z""hF›F’˜’Fz""›Fd©˜§a›^˜›^F˜˜z""hF›F˜O¤m4›apm’˜ p¤˜4"m˜¤’F˜
›^F˜˜z""hF›F’˜Op˜zpV"hhamV˜h"›^Fh"›a4"d˜O¤m4›apm’˜›^"›˜
4pm›pd˜zpV"h˜F¨F4¤›apm˜p˜=F’4a*F˜"˜4pm›p¤
pV"hhamV˜§a›^˜˜z""hF›F’˜a’˜=F’4a*F=˜am˜ ^"z›F˜s¬
L
L
L
CC
C
X
Y
R40
115 10
80
60
40
CC