Comtech EF Data CSAT-5060 - Manual (Page 11)

CSAT-5060 C-Band Satellite Transceivers Revision 1
Table of Contents MN/CSAT5060.IOM
ix
FIGURE 8‐4. SWITCH PORT LOCATIONS .................................................................................................................... 8–5
FIGURE 8‐5. INSTALLATION OF SINGLE‐THREAD LNA .............................................................................................. 8–6
FIGURE 8‐6. INSTALLATION OF THE REDUNDANT LNA ASSEMBLY. .......................................................................... 8–7
FIGURE 9‐1. J8 CONNECTOR FOR EXTERNAL AMPLIFIER COMMUNICATION ........................................................... 9–6
FIGURE A‐1. UNIVERSAL POLE MOUNTING KIT, AS/0414 ........................................................................................ A–3
FIGURE A‐2. SINGLE‐THREAD BRACKET, AS/0608 .................................................................................................... A–4
FIGURE A‐3. SINGLE‐ THREAD INSTALLATION .......................................................................................................... A–5
FIGURE A‐4. PREPARING THE POLE BRACKET .......................................................................................................... A–5
FIGURE A‐5. INSTALLING THE POLE BRACKET WITH CSAT MOUNTING PLATE. ........................................................ A–6
FIGURE A‐6. CSAT SINGLE‐THREAD BRACKET WITH HARDWARE ............................................................................ A–7
FIGURE A‐7. INSTALL CSAT SINGLE‐THREAD BRACKET ............................................................................................. A–7
FIGURE A‐8. MOUNT CSAT UNIT .............................................................................................................................. A–7
FIGURE A‐9. CABLE CONNECTIONS .......................................................................................................................... A–8
FIGURE A‐11. SPAR MOUNT KIT, KT/9676‐1 OR KT/9676‐2 .................................................................................. A–10
FIGURE 3‐10. SPAR MOUNT KIT, KT/9676‐1 OR KT/9676‐2 ................................................................................... A–10
FIGURE A‐12. MOUNTING INSTRUCTIONS ............................................................................................................. A–11
FIGURE A‐13. CABLE CONNECTIONS ...................................................................................................................... A–12
FIGURE A‐14. REDUNDANCY CONFIGURATION ..................................................................................................... A–13
FIGURE A‐15. 1:1 25W CSAT TX SWITCH BRACKET, AS/0489 ................................................................................ A–14
FIGURE A‐16. CABLE KIT, AS/0440 ......................................................................................................................... A–15
FIGURE A‐17. REMOTE SWITCH BOX ASSEMBLY, AS/0490 .................................................................................... A–16
FIGURE A‐18. TX/REMOTE SWITCH ASSEMBLY, AS/0503 ...................................................................................... A–17
FIGURE A‐19. CONNECTIONS FOR THE TX/REMOTE SWITCH PORTS (50Ω TERMINATION AND ATTENUATOR
INSTALLED) ..................................................................................................................................................... A–18
FIGURE A‐20. REMOTE SWITCH CAST BOX AND HARDWARE ................................................................................. A–19
FIGURE A‐21. INSTALLATION OF THE REDUNDANT BRACKETS .............................................................................. A–20
FIGURE A‐22. INSTALLATION OF THE CSAT TRANSCEIVERS ................................................................................... A–21
FIGURE A‐23. CABLE THE REDUNDANT CONFIGURATION ..................................................................................... A–21
FIGURE A‐24. CABLING THE REDUNDANT CONFIGURATION (BLOCK DIAGRAM) ................................................. A–23
FIGURE B‐1. UNIVERSAL POLE MOUNTING KIT, AS/0414 ........................................................................................ B–3
FIGURE B‐2. CSAT MOUNTING BRACKETS, AS/0415 ................................................................................................ B–4
FIGURE B‐3. SINGLE‐THREAD CONFIGURATION ...................................................................................................... B–5
FIGURE B‐4. INSTALLING THE POLE BRACKET ........................................................................................................... B–6
FIGURE B‐5. LOOKING DOWN .................................................................................................................................. B–6
FIGURE B‐6. INSTALL CSAT 50 WATT UNIT .............................................................................................................. B–8
FIGURE B‐7. CSAT SINGLE‐THREAD BRACKET ......................................................................................................... B–8
FIGURE B‐8. CABLE CONNECTIONS .......................................................................................................................... B–9
FIGURE B‐9. TX SWITCH MOUNTING KIT, AS/0437 ................................................................................................ B–11
FIGURE B‐10. CABLE KIT ......................................................................................................................................... B–12
FIGURE B‐11. WAVEGUIDE KIT, CPR137G, AS/0460 (FOR MOUNTING CUSTOMER‐SUPPLIED UNIT TO TRANSMIT
SWITCH ASSEMBLY) ....................................................................................................................................... B–13
FIGURE B‐12. WAVEGUIDE SWITCH, TX 1:1, AS/0462 ............................................................................................ B–14
FIGURE‐B‐13. REMOTE SWITCH BOX ASSEMBLY, AS/0490 .................................................................................... B–15
FIGURE B‐14. REDUNDANT CONFIGURATION ........................................................................................................ B–16
FIGURE B‐15. ASSEMBLE WAVEGUIDE SWITCH, AS/0462 ...................................................................................... B–17
FIGURE B‐16. PREPARING THE POLE BRACKET ...................................................................................................... B–18
FIGURE B‐17. PIPE BLOCKS .................................................................................................................................... B–19
FIGURE B‐18. LOOKING DOWN AT PIPE BLOCKS .................................................................................................... B–19
FIGURE B‐20. INSTALLATION OF THE WAVEGUIDE SWITCH. .................................................................................. B–21
FIGURE B‐19. POSITION BRACKETS AGAINST CENTER BRACKET............................................................................ B–21
FIGURE B‐21. CABLE INSTALLATION ...................................................................................................................... B–23