Reznor SHH (Indoor PreevA) Unit Installation Manual - Manual (Page 8)

Form I-PDH/SDH/PEH/SHH/PXH, Page 8
4.2 Configurations
and Dimensions
Option ECC3
or ECC2
Evaporative
Cooling
Module
Option MXB1
Mixing Box
with Variety
of Inlet Air
Options
Optional
On/Off Damper
Option AU Cooling
Coil Module with
a DX or Chilled Water
Coil with or without
Reheat
Blower and Heat Section
(SDH, PDH, SHH, or PEH);
Blower only (PXH - “no
heat” model only; for PXH
with optional hot water heat
module, see page 40.)
Use this column to
determine which length
measurements apply to
the system.
Air Flow
ECC MXB1 AR8 AU 5, 6, or 7 BASIC
KEY to Dimension Codes A,
C, and E in TABLE 4 and
FIGURE 2
-- -- -- -- Basic A, C, E
-- -- AR8 -- Basic A, C + 10" (254mm), E
-- MXB1 -- -- Basic A1, C1, E1
ECCx -- -- -- Basic A1, C1, E1
-- -- -- AU 5 or 6 w/o Reheat Basic A2, C2, E2
-- -- AR8 AU 5 or 6 w/o Reheat Basic A2, C2 + 10" (254mm), E2
-- -- -- AU 7 with Reheat Basic A3, C3, E3
-- -- AR8 AU 7 with Reheat Basic A3, C3 + 10" (254mm), E3
ECCx MXB1 -- -- Basic A4, C4, E4
-- MXB1 -- AU 5 or 6 w/o Reheat Basic A5, C5, E5
-- MXB1 -- AU 7 with Reheat Basic A6, C6, E6
ECCx -- -- AU 5 or 6 w/o Reheat Basic A5, C5, E5
ECCx -- -- AU 7 with Reheat Basic A6, C6, E6
ECCx MXB1 -- AU 5 or 6 w/o Reheat Basic A7, C7, E7
ECCx MXB1 -- AU 7 with Reheat Basic A8, C8, E8
FIGURE 1 - Factory-
assembled
Configurations
Depending on Option
Selection and KEY to
Dimensions A, C, and E
TABLE 4 - Dimensions
Important NOTES:
1) Dimensions A, C, and E
change with selection of factory-
installed modules; see Key
above.
2) Suspension Point Dimensions
U, V, and W apply ONLY to sys-
tems with a cooling coil cabinet
(AU) and/or a mixing box (MXB).
A system with one module (AU
or MXB) has two intermediate
side hangers; a system with two
modules (MXB and AU) has four
intermediate side hangers.
The basic unit and the basic unit
with an evaporative cooling mod-
ule (ECC) do not require interme-
diate side suspension points.
3) Dimension W1 applies to both
a mixing box (MXB) and a coil
cabinet without reheat (AU5 or
AU6); W2 applies to a mixing box
(MXB) and a coil cabinet with
reheat (AU7).
4) PXH dimensions are for “no
heat” model only. Dimensions for
PXH with hot water heat are in
Paragraph 6.7.5.
Dimensions - inches (±1/8)
PDH or
SDH PEH SHH PXH
Dimensions (See FIGURES 1 and 2) - apply to all Models unless specified
A A1 A2 A3 A4 A5 A6 A7 A8 B C C1
75, 100 10A, 20A, 40A N/A 000A 56-5/8 87-11/16 84-7/16 109-1/2 118-3/4 115-15/32 140-7/8 146-1/2 171-9/16 32-5/8 54-3/4 85-13/16
125, 150 15B, 30B, 60B N/A 000B 56-5/8 87-11/16 84-7/16 109-1/2 118-3/4 115-15/32 140-7/8 146-1/2 171-9/16 42-5/8 54-3/4 85-13/16
175, 200,
225 N/A
130,
180 000C PDH/SDH/
PEH /PXH
72-5/16
SHH
82-5/16
PDH/SDH/
PEH/PXH
103-5/8
SHH
113-5/8
PDH/SDH/
PEH/PXH
100-1/8
SHH
110-1/8
PDH/SDH/PEH/
PXH
125-3/16
SHH
135-3/16
PDH/SDH/
PEH/PXH
134-7/16
SHH
144-7/16
PDH/SDH/
PEH/PXH
131-3/16
SHH
141-3/16
PDH/SDH/
PEH/PXH
156-1/4
SHH
166-1/4
PDH/SDH/
PEH/PXH
162-1/4
SHH
172-1/4
PDH/SDH/
PEH/PXH
187-5/16
SHH
197-5/16
32-5/8 PDH/SDH/
PEH/PXH
70-7/16
SHH
80-7/16
PDH/SDH/
PEH/PXH
101-1/2
SHH
111-1/2
250, 300
30D, 60D, 90D,
120D 260 000D 48-7/8
350, 400A 40E, 80E, 120E 350 000E 56-7/8
PDH or
SDH
PEH SHH PXH
Dimensions (See FIGURES 1 and 2) - apply to all Models unless specified
C2 C3 C4 C5 C6 C7 C8 D -
SDH/SHH
E E1 E2 E3
75, 100 10A, 20A, 40A N/A 000A 82-9/16 107-5/8 116-7/8 113-5/8 138-11/16 144-11/16 169-3/4 4 59-5/8 90-21/32 87-13/32 112-15/32
125, 150 15B, 30B, 60B N/A 000B 82-9/16 107-5/8 116-7/8 113-5/8 138-11/16 144-11/16 169-3/4 4 59-5/8 90-21/32 87-13/32 112-15/32
175, 200,
225 N/A
130,
180 000C PDH/SDH/
PEH/PXH
98-7/32
SHH
108-7/32
PDH/SDH/
PEH/PXH
123-9/32
SHH
133-9/32
PDH/SDH/
PEH/PXH
132-9/16
SHH
142-9/16
PDH/SDH/PEH/
PXH
129-19/64
SHH
139-19/64
PDH/SDH/
PEH/PXH
154-23/64
SHH
164-23/64
PDH/SDH/
PEH/PXH
160-11/32
SHH
170-11/32
PDH/SDH/
PEH/PXH
185-13/32
SHH
195-13/32
5 PDH/SDH/
PEH/PXH
75-5/16
SHH
85-5/16
PDH/SDH/
PEH/PXH
106-3/8
SHH
116-3/8
PDH/SDH/
PEH/PXH
103-7/64
SHH
113-7/64
PDH/SDH/
PEH/PXH
128-11/64
SHH
138-11/64
250, 300 30D, 60D, 90D,
120D
260 000D 5
350, 400A 40E, 80E, 120E 350 000E 5
PDH or
SDH PEH SHH PXH
Dimensions (See FIGURES 1 and 2) - apply to all Models unless specified
E4 E5 E6 E7 E8
F - PDH/
SDH/SHH
G - PDH/
SDH/SHH
H -
SDH/SHH
J - PDH/
SDH/SHH
K * M N
75, 100 10A, 20A, 40A N/A 000A 121-23/32 118-15/32 143-17/32 149-17/32 174-19/32 20-25/32 17-7/8 3-5/8 16-51/64 33-3/4 24-11/16 34-15/32
125, 150 15B, 30B, 60B N/A 000B 121-23/32 118-15/32 143-17/32 149-17/32 174-19/32 20-25/32 17-7/8 3-5/8 16-51/64 43-3/4 34-11/16 34-15/32
175, 200,
225
N/A 130,
180
000C PDH/SDH/
PEH/PXH
137-7/16
SHH
147-7/16
PDH/SDH/
PEH/PXH
134-11/64
SHH
144-11/64
PDH/SDH/
PEH/PXH
162-1/2
SHH
172-1/2
PDH/SDH/PEH/
PXH
165-1/4
SHH
175-1/4
PDH/SDH/
PEH/PXH
190-5/16
SHH
200-5/16
PDH/SDH
32-1/32
SHH
42-15/16
PDH/SDH
24-3/4
SHH
35-5/8
4
PDH/SDH
17-7/32
SHH
17-7/16
33-3/4 24-11/16 43-23/32
250, 300
30D, 60D, 90D,
120D 260 000D 4 50 40-15/16 43-23/32
350, 400A 40E, 80E, 120E 350 000E 4 58 48-15/16 43-23/32
PDH or
SDH
PEH SHH PXH
Dimensions (See FIGURES 1 and 2) - apply to all Models unless specified
P Q R S T U V W1 W2 X- PEH
75, 100 10A, 20A, 40A N/A 000A 27-11/32 17-23/32 5-3/64 13-13/16 2-27/32 35-3/4 55-15/32 83-1/4 108-5/16 21-11/16
125, 150 15B, 30B, 60B N/A 000B 27-11/32 27-23/32 5-3/64 13-13/16 2-27/32 45-3/4 55-15/32 83-1/4 108-5/16 21-11/16
175, 200,
225 N/A
130,
180 000C 36-9/16 20-29/32 2 23 2-59/64 35-3/4 71-5/32 98-61/64 PDH/SDH/
PEH/PXH
124-1/64
SHH
134-1/64
N/A
250, 300
30D, 60D, 90D,
120D 260 000D 36-9/16 28-13/16 10-5/16 23 2-59/64 52 71-5/32 98-61/64 29-3/8
350, 400A 40E, 80E, 120E 350 000E 36-9/16 38-15/32 8-41/64 23 2-59/64 60 71-5/32 98-61/64 29-3/8
Dimensions - mm (±3)
PDH or
SDH
PEH SHH PXH
Dimensions (See FIGURES 1 and 2) - apply to all Models unless specified
A A1 A2 A3 A4 A5 A6 A7 A8 B C C1 C2 C3 C4 C5 C6 C7 C8 D- SDH/
SHH
E E1 E2
75, 100 10A, 20A, 40A N/A 000A 1438 2227 2144 2781 3016 2933 3578 3722 4359 829 1391 2180 2097 2734 2969 2886 3523 3675 4312 102 1514 2303 2220
125, 150 15B, 30B, 60B N/A 000B 1438 2227 2144 2781 3016 2933 3578 3722 4359 1083 1391 2180 2097 2734 2969 2886 3523 3675 4312 102 1514 2303 2220
175, 200,
225
N/A 130,
180
000C
PDH/
SDH/
PEH/
PXH
1837
SHH
2091
PDH/
SDH/
PEH/
PXH
2626
SHH
2880
PDH/
SDH/
PEH/
PXH
2543
SHH
2797
PDH/
SDH/
PEH/
PXH
3180
SHH
3434
PDH/
SDH/
PEH/
PXH
3415
SHH
3669
PDH/
SDH/
PEH/
PXH
3332
SHH
3586
PDH/SDH/
PEH/PXH
3969
SHH
4223
PDH/SDH/
PEH/PXH
4121
SHH
4375
PDH/SDH/
PEH/PXH
4758
SHH
5012
829
PDH/
SDH/
PEH/
PXH
1789
SHH
2043
PDH/
SDH/
PEH/
PXH
2578
SHH
2832
PDH/
SDH/
PEH/
PXH
2495
SHH
2749
PDH/
SDH/
PEH/
PXH
313
SHH
N/A
PDH/
SDH/
PEH/
PXH
3367
SHH
N/A
PDH/
SDH/
PEH/
PXH
3284
SHH
3538
PDH/
SDH/
PEH/
PXH
3921
SHH
N/A
PDH/
SDH/
PEH/
PXH
4073
SHH
N/A
PDH/
SDH/
PEH/
PXH
4711
SHH
N/A
127 PDH/
SDH/
PEH/PXH
1913
SHH
2167
PDH/
SDH/
PEH/PXH
2702
SHH
2956
PDH/
SDH/
PEH/
PXH
2619
SHH
2873
250, 300
30D, 60D, 90D,
120D 260 000D 1241 127
350, 400A 40E, 80E, 120E 350 000E 1445 127
PDH or
SDH
PEH SHH PXH
Dimensions (See FIGURES 1 and 2) - apply to all Models unless specified
E3 E4 E5 E6 E7 E8
F G
H- SDH/
SHH
J- PDH/SDH/
SHH
K* M N P Q R S T U V W1 W2 X -
PEH PDH/SDH/SHH
75, 100 10A, 20A, 40A N/A 000A 2856 3092 3009 3646 3798 4435 528 454 92 427 857 627 876 695 450 128 351 72 908 1409 2115 2751 551
125, 150 15B, 30B, 60B N/A 000B 2856 3092 3009 3646 3798 4435 528 454 92 427 1111 881 876 695 704 128 351 72 1162 1409 2115 2751 551
175, 200,
225
N/A 130,
180
000C
PDH/
SDH/
PEH/
PXH
3256
SHH
3510
PDH/
SDH/
PEH/
PXH
3491
SHH
3745
PDH/
SDH/
PEH/
PXH
3009
SHH
3263
PDH/
SDH/
PEH/
PXH
4128
SHH
4382
PDH/
SDH/
PEH/
PXH
4197
SHH
4451
PDH/
SDH/
PEH/
PXH
4834
SHH
5098
PDH/SDH
814
SHH 1091
PDH/SDH
629
SHH
905
102
PDH/SDH
437
SHH
443
857 627 1111 928 531 51 584 74 908 1807 2513 PDH/
SDH/
PEH/PXH
3150
SHH
3404
N/A
250, 300 30D, 60D, 90D,
120D
260 000D 102 1270 1040 1111 928 732 262 584 74 1321 1807 2513 746
350, 400A 40E, 80E, 120E 350 000E 102 1473 1243 1111 928 977 219 584 74 1524 1807 2513 746
* Model SHH - See FIGURE 2, Front View, for additional width from factory-installed flue connection
4.0 Dimensions
and Clearances
(cont’d)
* Model SHH -
See FIGURE 2,
Front View, for
additional width
from factory-
installed flue
connection.