Reznor SHH (Indoor PreevA) Unit Installation Manual - Manual (Page 10)

Form I-PDH/SDH/PEH/SHH/PXH, Page 10
5.0 Suspension
and Mounting
TABLE 5 - Weights
(lbs and kg) of Basic
System and Factory-
Installed Optional
Modules
5.1 Weights
Before installing, check the support structure to be sure that it has sufficient load-bear-
ing capacity to support the weight of unit during installation and operation. Suspension
or mounting is the responsibility of the installer.
TABLE 6 - Corner
Weights of Heat Module
and Blower Section
only for Models Listed
control side
Important NOTES: If controls are on the right side, switch left and right side weights.
Weights do not include the blower motor or any optional modules.
FIGURE 3 - Corner
Weight Locations
Model PDH and Model SDH (gas-fired heat) 75 100 125 150 175 200 225 250 300 350 400A
Model PEH (electric heat) 10A, 20A, 40A 15B, 30B, 60B N/A 30D, 60D, 90D, 120D 40E, 80E, 120E
Model SHH (high efficiency gas-fired heat) N/A 130 180 --- 260 -- 350 --
Model PXH (no heat) 000A 000B 000C 000D 000E
Approximate Net Weights - lbs (does not include motor weight)
Basic Gas Heat & Blower Section (PDH or SDH) 323 331 413 421 478 492 492 615 629 721 732
Basic Electric Heat & Blower Section (PEH) 296 368 N/A 523 594
Basic High Efficiency Gas Heat & Blwr Sctn (SHH) N/A 538 544 -- 729 -- 889 --
Blower Section (PXH) 245 307 333 431 483
Approximate Weights (lbs) of factory-attached options (add to weight listed above)
Option AR8, on/off damper (no mixing box)
34 45 56 73 85
Option MXB1
Mixing Box Module
w/o Dampers
2 inlets, single wall 119 132 134 159 174
2 inlets, double wall 146 165 166 199 216
1 inlet, single wall 115 127 130 154 169
1 inlet, double wall 146 166 166 201 219
Cooling Coil
Module with
heaviest coil
weight*
DX coil without
reheat pump
4 row coil 214 252 256 329 365
6 row coil 235 280 284 373 418
DX coil with
reheat pump
4 row coil 331 382 394 494 547
6 row coil 352 410 422 538 600
Chilled water
(filled)
4 row coil 301 363 373 497 559
6 row coil 351 431 441 604 686
Evaporative
Cooling Module
with dry media 12" media 120 141 136 172 190
with wet media &
3" of water
12" media 262 263 218 279 272
Hot Water Heat Module - for PXH with
HW2 only (does not include water wt)
w/4 row,
14 fpi coil
145 175 177 236 263
Approximate Net Weights - kg (does not include motor weight)
Basic Gas Heat & Blower Section (PDH or SDH) 147 150 187 191 217 223 223 279 285 327 332
Basic Electric Heat & Blower Section (PEH) 134 167 N/A 237 269
Basic High Efficiency Gas Heat & Blwr Sctn (SHH) N/A 244 247 -- 331 -- 403 --
Blower Section (PXH) 111 139 151 195 219
Approximate Weights (kg) of factory-attached options (add to weight listed above)
Option AR8, on/off damper (no mixing box) 15 20 25 33 39
Option MXB1 Mixing
Box Module w/o
Dampers
2 inlets, single wall 54 60 61 72 79
2 inlets, double wall 66 75 75 90 95
1 inlet, single wall 52 58 59 70 77
1 inlet, double wall 66 75 75 91 99
Cooling Coil Module
with heaviest coil
weight*
DX coil without
reheat pump
4 row coil 97 114 116 149 166
6 row coil 107 127 129 169 190
DX coil with reheat
pump
4 row coil 150 173 179 224 248
6 row coil 160 186 191 244 272
Chilled water (filled)
4 row coil 137 165 169 225 254
6 row coil 159 195 200 274 311
Evaporative Cooling
Module
with dry media 12" media 54 64 62 78 86
with wet media &
76mm of water
12" media 119 119 99 127 123
Hot Water Heat Module - for PXH with
HW2 only (does not include water weight)
w/4 row,
14 fpi coil
66 79 80 107 119
* Cooling coil cabinet
module weight is
estimated for heaviest
coil. If more accurate
information is needed,
check with your
distributor or Reznor ®
Representative who
either has the specific
information in the order
specifications or has
software to generate the
information.
5.2 Lifting and
Suspension
The heavy gauge base of the unit has forklift openings in both sides. See FIGURE
4. Use these openings to move and lift the unit. (NOTE: If system has more than two
optional modules, check for labels identifying which side to lift.) Braces underneath are
spaced to accommodate a minimum fork length of 24” (610mm).
In addition, the base of all units has a lifting hole at each corner. Systems with a mixing
box and/or a cooling cabinet have additional side suspension points. When lifting, lift
from all of the suspension points on the unit (4, 6, or 8). Use spreader bars to lift the
unit straight up with vertical force only.
Top View
SHH 130 180 260 350
Corner
(FIG 3)
Approx Wt (lbs) - Heat
Section & Blower only
LR 81 82 127 188
RR 87 88 144 192
RF 193 193 241 264
LF 180 180 217 245
Corner
(FIG 3)
Approx Wt (kg) - Heat
Section & Blower only
LR 37 37 58 85
RR 39 40 65 87
RF 88 88 109 120
LF 82 82 98 120
PEH 10A, 20A, 40A 15B, 30B, 60B 30D, 60D, 90D, 120D 40E, 80E, 120E
Approx Wt of
Each Corner
lbs kg lbs kg lbs kg lbs kg
74 34 92 42 131 59 149 68
PDH/SDH 75 100 125 150 175 200 225 250 300 350 400A
Corner (FIGURE 3) Approximate Corner Weights (lbs) - Heat Section & Blower only
LR 70 70 92 92 80 80 80 124 124 158 158
RR 63 63 87 87 74 74 74 110 110 155 155
RF 92 96 113 117 156 163 163 180 187 198 202
LF 98 102 121 125 168 175 175 201 208 210 217
Corner (FIGURE 3) Approximate Corner Weights (kg) - Heat Section & Blower only
LR 32 32 42 42 36 36 36 56 56 72 72
RR 29 29 39 39 34 34 34 50 50 70 70
RF 42 44 51 53 71 74 74 82 85 90 92
LF 44 46 55 57 76 79 79 91 94 95 98