Rockwell Automation WebPak 3000 DC Drive Application Workbook Version 1.1 - Manual (Page 99)

Index Index-1
I
NDEX
A
AC line, 13-3
ACCELERATION TIME (P.001), 3-9
Analog inputs, A-10
Analog outputs, 13-1, A-10
ANALOG TACH FEEDBACK (P.291), 3-13
ANALOG TACH GAIN ADJ (P.201), 3-13
ANALOG TACH ZERO ADJ (P.202), 3-13
ANALOG TRIM REF (P.195), 3-4
ANLG OUT 1 FILTER EN (P.406), 13-2
ANLG OUT 1 GAIN ADJ (P.400), 13-2
ANLG OUT 1 SELECT (P.404), 10-6
ANLG OUT 1 ZERO ADJ (P.402), 13-2
ANLG OUT 2 FILTER EN (P.407), 13-2
ANLG OUT 2 GAIN ADJ (P.401), 13-2
ANLG OUT 2 SELECT (P.405), 13-2
ANLG OUT 2 ZERO ADJ (P.403), 13-2
ANLG OUT 3 GAIN ADJ (P.420), 9-5, 13-2
ANLG OUT 3 SELECT (P.418), 9-4, 13-2
ANLG OUT 3 SIG TYPE (P.419), 9-5, 13-2
ANLG OUT 4 GAIN ADJ (P.422), 13-2
ANLG OUT 4 SELECT (P.421), 13-2
ANLG TACH VOLTS /1000 (P.203), 3-13
Application guidelines
current regulators, A-3
flying splice unwinds, A-7
flying transfer winders, A-8
position regulators, A-4
speed regulators, A-3
tension regulators, A-5
voltage and field control, A-6
ARM VOLTAGE GAIN ADJ (P.204), 13-4
ARM VOLTAGE ZERO ADJ (P.205), 13-4
ARMATURE BRIDGE POL (P.394), 4-4
ARMATURE DELTA (P.399), 4-4
ARMATURE VOLTAGE (P.289), 5-5
Armature voltage feedback, 13-4
Automatic field weakening, 5-5
B
BASE SPEED (P.017), 7-2
BUILDUP CONSTANT (P.871), 7-1, 7-2
C
CML ERROR (P.398), 4-1
CML FEEDBACK (P.397), 3-12, 4-4
CML FEEDBACK GAIN ADJ (P.300), 4-4
CML PI LEAD FREQUENCY (P.302), 4-5
CML PI PROP GAIN (P.301), 4-5
CML RAMP INPUT TP (P.390), 4-2
CML REF LIMIT SELECT (P.311), 4-2, 4-3
CML REF RATE LIMIT (P.303), 4-2, 4-3
CML REFERENCE (P.396), 4-2, 4-3, 4-4
CML SPEED REFERENCE (P.391), 4-1
CONTROL SOURCE SELECT (P.000), 3-2
Control source, selecting, 3-2
CT TURNS RATIO (P.010), 4-4, 4-5
CURRENT COMPOUND TP (P.293), 3-12
Current compounding, 3-12
CURRENT COMPOUNDING (P.209), 3-12
Current major outer control loop, configuring, 10-1
CURRENT MEM COMMAND (P.319), 3-17
CURRENT MEMORY BOOST (P.313), 3-17
CURRENT MEMORY DIN TP (P.499), 3-17
CURRENT MEMORY ENABLE (P.314), 3-17
Current memory function, 3-17
Current minor loop
configuring, 4-1
configuring the reference, 4-1
configuring the regulator, 4-4
CURRENT / SPEED SWITCH (P.811), 4-3
D
DANCER ACCEL TIME (P.873), 9-4
DANCER DECEL TIME (P.819), 9-4
Dancer loading
configuring, 9-4
setup example, 9-5
DANCER LOADING (P.820), 9-4
DECELERATION TIME (P.002), 3-8, 3-9
DIAMETER ACCEL RATE (P.823), 6-3
DIAMETER ANALOG (P.821), 6-3
DIAMETER CALC ENABLE (P.826), 3-5, 6-3, 6-4
DIAMETER CALC OUTPUT (P.132), 6-4
Diameter calculator, 6-2, A-7
configuring, 6-1
validating the setup of, 6-4