Datamax-O'Neil I-Class Operator’s Manual User Manual
Page 74
64
I-Class
Standard Calibration (continued)
Step
Action
Displayed Message
Comment
9 Observe the LCD.
GAP MODE
CALIBRATION COMPLETE
Or, for reflective media:
REFLECTIVE MODE
CALIBRATION COMPLETE
Or, for continuous media:
CONTINUOUS MODE
CALIBRATION COMPLETE
The calibration was
successful if
CALIBRATION COMPLETE
appears.
(If, however, another
message was displayed
see Note 1, below.)
10
Press the
Key three
times to exit the menu.
Users of circular or
irregularly shaped die-cut
media see Note 2 before
proceeding.
If using gap, notch or
reflective media, press and
hold the FEED Key. Allow
at least one label to
advance from the printer
before releasing the key.
READY
The printer is ready.
If this calibration was
unsuccessful, go to
Section 5.2.2.
Notes:
(1) WARNING LOW
BACKING is a normal
message when
calibrating notched media
or media with
transparent backing; see
Section 6.1.2 for other
possible messages.
(2) If using circular or
irregularly shaped die-cut
labels, reposition the
Sensor Eye Mark over the
widest part of a label.
- MF8I 270 User Guide (20 pages)
- MF8I Installation Guide (18 pages)
- MF8I Truck Mount Cable (2 pages)
- MF8I Locking Mounting Bracket (2 pages)
- MF8I Economy Mounting Bracket (2 pages)
- MF8I AN-15 (Line Printer and Easy Print Modes) (7 pages)
- MF8I AN-16 (Single Byte Character Set Font File Format) (8 pages)
- MF8I Quick Reference Programming Guide (72 pages)
- MF8I Configuration Program Installation (1 page)
- MF8I Bluetooth Management Component for Wavelink Avalanche (10 pages)
- A-Class Mark II Operator’s Manual (160 pages)
- A-Class Mark II Installation (2 pages)
- A-Class Mark II DMXrfNetIII (16 pages)
- A-Class Mark II DMXrfNetII (16 pages)
- A-Class Mark II RFID Quick Start Guide (6 pages)
- A-Class Mark II Programmer’s Manual (334 pages)
- ANDES 3 User Guide (32 pages)
- ANDES 3 Quick Start Guide (2 pages)
- ANDES Series Programmer’s Manual (67 pages)
- APEX 2 User Guide (28 pages)
- APEX 2 Quick Start Guide (2 pages)
- APEX 3 User Guide (27 pages)
- APEX 3 Quick Start Guide (2 pages)
- APEX 4 User Guide (30 pages)
- APEX 4 Quick Start Guide (2 pages)
- E-Class Mark III Operator’s Manual (90 pages)
- E-Class Mark III 4xxxxxxx Operator’s Manual (58 pages)
- E-Class Mark III 3xxxxxxx Operator’s Manual (58 pages)
- E-Class Mark III Paper Menu (7 pages)
- E-Class Mark III DPL Programmer’s Manual (296 pages)
- E-Class Mark III Printhead Bracket and Screw Upgrade (11 pages)
- H-Class Operator’s Manual (180 pages)
- Static brush (2 pages)
- H-Class Media Retainer (1 page)
- H-Class Thermal Transfer Option (12 pages)
- H-Class RFID Option (8 pages)
- H-Class Powered Internal Rewind Option (10 pages)
- H-Class Internal Rewind Option (6 pages)
- H-Class Present Sensor Option (8 pages)
- H-Class Peel & Present Option (8 pages)
- H-Class Linear Scanner Option (26 pages)
- H-Class HD Peel & Present Option (10 pages)
- H-Class HD Cutter Option (12 pages)
- H-Class GPIO Option (14 pages)
- H-Class Cutter Option (10 pages)