Index – HEIDENHAIN TNC 320 (34055x-06) User Manual

Page 537

TNC 320 | User's Manual HEIDENHAIN Conversational Programming | 5/2013

537

Index

3-D touch probes

Calibration.............................. 406

3-D view................................... 442

Accessing tables...................... 269
Accessories................................ 76
Actual position capture............... 89
Adding comments.................... 117
Additional axes..................... 81, 81
Adjusting spindle speed........... 391
Angle functions........................ 242
Approach contour..................... 174
ASCII Files................................ 337
Automatic program start.......... 460
Automatic tool measurement... 147

Basic rotation........................... 412

Measuring in Manual Operation
mode...................................... 412

Block.......................................... 91

Delete...................................... 91

Calculating with parentheses... 279
Calculation of circles................ 243
Calculator................................. 120
Chamfer................................... 184
Circle........................ 188, 190, 196
Circle center............................. 186
Circular path..................... 187, 196
Code numbers......................... 468
Comparison.............................. 510
Compensating workpiece
misalignment

By measuring two points on a
straight surface...................... 411

Connecting/removing USB devices.
113
Connector pin layout for data
interfaces................................. 498
Context-sensitive help.............. 131
Control panel.............................. 66
Conversational dialog................. 87
Coordinate transformation........ 334
Copying program sections.... 92, 92
Corner rounding....................... 185

Data Backup............................... 97
Data interface........................... 470

Connector pin layouts............ 498
Set up.................................... 470

Data output on the screen....... 256
Data transfer software............. 474

Data transfer speed....
470, 471, 471, 471, 471, 472, 472
Datum management................ 393
Datum setting.......................... 392

Without a 3-D touch probe..... 392

Datum shift

Resetting................................ 336
Using the datum table............ 335

Datum table............................. 404

Transferring test results.......... 404

Defining local Q parameters..... 238
Defining nonvolatile Q parameters..
238
Defining the workpiece blank..... 86
Depart contour......................... 174
Dialog......................................... 87
Directory............................ 98, 102

Copy....................................... 105
Create.................................... 102
Delete.................................... 106

Display screen............................ 65
Downloading help files............. 136

Enter spindle speed................. 156
Error messages................ 125, 125

Help with............................... 125

Ethernet interface.................... 476

Connecting and disconnecting
network drives....................... 112
Connection options................ 476
Introduction............................ 476

External access........................ 469
External data transfer

iTNC 530................................ 110

FCL........................................... 468
FCL function................................ 9
Feature Content Level.................. 9
Feed rate.................................. 390

Adjust..................................... 391
Input options............................ 88
On rotary axes, M116............. 370

Feed rate factor for plunging
movements M103.................... 313
Feed rate in millimeters per spindle
revolution M136....................... 314
File

Create.................................... 102

File functions............................ 333
File manager........................ 95, 98

Call......................................... 100
Copying files.......................... 102
Copying tables....................... 104
Delete file.............................. 106
Directories................................ 98

Copy................................. 105

Create.............................. 102

External data transfer............. 110
File

Create.............................. 102

File type................................... 95
Function overview.................... 99
Overwriting files..................... 103
Protect file.............................. 109
Rename file.................... 108, 108
Selecting files......................... 101
Tagging files........................... 107

File status................................ 100
FK programming.............. 201, 201

Circular paths......................... 207
Fundamentals......................... 201

FK-Programming

Graphics................................. 203

FK programming

Initiating dialog....................... 205
Input options.......................... 208

Auxiliary points................. 211
Circle data........................ 209
Closed contours............... 210
Direction and length of

contour elements................. 208

End points........................ 208
Relative data.................... 212

Straight lines.......................... 206

Graphics................................... 438

Display modes....................... 440