H3C Technologies H3C S7500E Series Switches User Manual

Page 297

6-72

[ASBR-PE2-mpls] label advertise non-null

[ASBR-PE2-mpls] quit

[ASBR-PE2] mpls ldp

[ASBR-PE2-mpls-ldp] quit

# Configure interface VLAN-interface 11, start IS-IS and enable MPLS and LDP on the interface.

[ASBR-PE2] interface vlan-interface 11

[ASBR-PE2-Vlan-interface11] ip address 9.1.1.1 255.0.0.0

[ASBR-PE2-Vlan-interface11] isis enable 1

[ASBR-PE2-Vlan-interface11] mpls

[ASBR-PE2-Vlan-interface11] mpls ldp

[ASBR-PE2-Vlan-interface11] quit

# Configure interface Loopback 0 and start IS-IS on it.

[ASBR-PE2] interface loopback 0

[ASBR-PE2-LoopBack0] ip address 4.4.4.9 32

[ASBR-PE2-LoopBack0] isis enable 1

[ASBR-PE2-LoopBack0] quit

# Configure interface VLAN-interface 12 and enable MPLS on it.

[ASBR-PE2] interface vlan-interface 12

[ASBR-PE2-Vlan-interface12] ip address 11.0.0.1 255.0.0.0

[ASBR-PE2-Vlan-interface12] mpls

[ASBR-PE2-Vlan-interface12] quit

# Create routing policies.

[ASBR-PE2] route-policy policy1 permit node 1

New Sequence of this List

[ASBR-PE2-route-policy1] apply mpls-label

[ASBR-PE2-route-policy1] quit

[ASBR-PE2] route-policy policy2 permit node 1

[ASBR-PE2-route-policy2] if-match mpls-label

[ASBR-PE2-route-policy2] apply mpls-label

[ASBR-PE2-route-policy2] quit

# Start BGP on ASBR-PE 2 and specify to inject routes of IS-IS process 1.

[ASBR-PE2] bgp 600

[ASBR-PE2-bgp] import-route isis 1

# Configure the capability to advertise labeled routes to IBGP peer 5.5.5.9 and to receive labeled
routes from the peer.

[ASBR-PE2-bgp] peer 5.5.5.9 as-number 600

[ASBR-PE2-bgp] peer 5.5.5.9 connect-interface loopback 1

[ASBR-PE2-bgp] peer 5.5.5.9 label-route-capability

# Specify to use routing policy policy2 to filter routes advertised from IBGP peer 5.5.5.9.

[ASBR-PE2-bgp] peer 5.5.5.9 route-policy policy2 export

# Specify to use routing policy policy1 to filter routes advertised from EBGP peer 11.0.0.2.

[ASBR-PE2-bgp] peer 11.0.0.2 as-number 100

[ASBR-PE2-bgp] peer 11.0.0.2 route-policy policy1 export

# Configure the capability to advertise labeled routes to EBGP peer 11.0.0.2 and to receive labeled
routes from the peer.

[ASBR-PE2-bgp] peer 11.0.0.2 label-route-capability

[ASBR-PE2-bgp] quit

4) Configure PE 2