BINDER CB 60 User Manual

Operating manual, Apt.line™ cb (e6) co, Incubators co

This manual is related to the following products:

CB 160 CB 220 B 28 E 28 KMF 115 KMF 240 KMF 720

Table of contents

Document Outline

EG – declaration of conformity
Product registration
1. Safety
- 1.1 Legal considerations
- 1.2 Structure of the safety instructions
- 1.3 Localization / position of safety labels on the unit
- 1.4 Type plate
- 1.5 General safety instructions on installing and operating the CO2 incubator
- 1.6 Precautions when working with gases
- 1.7 Precautions when handling gas cylinders
- 1.8 Intended use
2. Unit description
- 2.1 Unit overview
- 2.2 Instrument panel
- 2.3 Inner chamber
- 2.4 Control panel on the rear of the unit
3. Completeness of delivery, transportation, storage, and installation
- 3.1 Unpacking, and checking equipment and completeness of delivery
- 3.2 Guidelines for safe lifting and transportation
- 3.3 Storage
- 3.4 Location of installation and ambient conditions
4. Installation and connections
- 4.1 Shelves
- 4.2 Permadry™ water pan
- 4.3 Gas connections
- 4.4 Electrical connection
- 4.5 Handling and aligning the multiple-divided inner glass door, gas proof (optional equipment)
5. Start up
- 5.1 Equilibration time
- 5.2 Factory settings
6. Functional overview of the T4.12 chamber controller
- 6.1 Menu structure
- 6.2 Operating modes
  - 6.2.1 Activating the “control off” mode or change to “fixed value” operating mode
- 6.3 Deactivating the O2 control and O2/N2 pressure alarms (unit with O2 control)
  - 6.3.1 Required gas supply of the unit with O2 control
  - 6.3.2 Activating / deactivating the O2 control and O2 / N2 pressure alarms
- 6.4 Humidity control of the Permadry™ system
- 6.5 Turning on / off the interior socket voltage (with optional interior socket)
- 6.6 Performance during and after power failure
- 6.7 Information
7. Setpoint entry
- 7.1 Setting ranges
- 7.2 Note when setting high gas concentrations
- 7.3 Entering the setpoints via “quick menu”
- 7.4 Entering the setpoints via general menu
8. Key lock
- 8.1 Directly activating the key lock
- 8.2 Automatic key lock
- 8.3 Changing the password for unlocking the key lock
9. General controller settings
- 9.1 Setup wizard
- 9.2 Date and time settings
- 9.3 Selecting the menu language of the T4.12 controller
- 9.4 Setting display brightness
- 9.5 Changing the temperature unit
- 9.6 Defining the data recording rate
- 9.7 Factory reset
- 9.8 Network configuration
- 9.9 Display of the network configuration
- 9.10 MAC Address
- 9.11 RS 422 address (with optional RS 422 interface)
- 9.12 Display and entry of the device configuration – for service purpose
10. Data transfer via USB interface
- 10.1 Exporting data to USB drive
- 10.2 Importing data from USB drive
11. Notifications and Alarms
- 11.1 Notifications overview
- 11.2 Alarm messages overview
- 11.3 Alarm status
- 11.4 Confirming an active “set” alarm
- 11.5 Alarm configuration and overview
- 11.6 Zero-voltage relay alarm output
12. Event list
13. Graphical display of the measured values
- 13.1 Setting the sampling rate
- 13.2 Defining the display range
- 13.3 Selecting the parameters
14. Temperature safety devices
- 14.1 Overtemperature protective device (class 1)
- 14.2 Overtemperature safety controller (temperature safety device class 3.1)
  - 14.2.1 Safety controller modes
  - 14.2.2 Setting the safety controller
15. Options
- 15.1 Communication software APT-COM™ 3 DataControlSystem (option)
- 15.2 RS 422 interface (option)
- 15.3 Silicone access ports 30 mm / 1.18 in, closable from both sides with silicon plugs (option)
- 15.4 Interior socket 230V (option)
- 15.5 Analog outputs for temperature and CO2 (option)
- 15.6 Access port for extra-low voltage (option)
- 15.7 BINDER Gas Supply Service – External bottle changer for CO2, N2 or O2 (option)
- 15.8 Stands
16. Reference measurements
- 16.1 CO2 reference measuring
- 16.2 Temperature reference measurement
17. Avoiding microbial contamination
- 17.1 Cells and media
- 17.2 Laboratory conditions / equipment around the incubator
- 17.3 Working and behavior in the lab
- 17.4 Chamber design and equipment of the CO2 incubator
- 17.5 Handling the CO2 incubator
18. Cleaning, decontamination / disinfection, and sterilization
- 18.1 Cleaning
- 18.2 Decontamination / chemical disinfection of the CO2 incubator
- 18.3 Hot-air sterilization at 180 °C / 356 °F
19. Maintenance and service
- 19.1 Maintenance intervals, service
- 19.2 Checking the air jacket heating fan
- 19.3 Checking the humidity system fan
- 19.4 Gas inlet fine filter
- 19.5 Sending the unit back to BINDER GmbH
20. Disposal
- 20.1 Disposal of the transport packing
  - 20.1.1 Outer unit packing
  - 1.1.1 Packing inside the unit and equipment
- 20.2 Decommissioning
- 20.3 Disposal of the unit in the Federal Republic of Germany
- 20.4 Disposal of the unit in the member states of the EC except for the Federal Republic of Germany
- 20.5 Disposal of the unit in non-member states of the EC
21. Troubleshooting
- 21.1 Heating
- 21.2 Gas cylinder pressure too low
- 21.3 Gas concentration
- 21.4 Sterilization
- 21.5 Humidity
- 21.6 Controller
- 21.7 Open door
22. Technical description
- 22.1 Factory calibration and adjustment
- 22.2 Over current protection
- 22.3 Definition of usable volume
- 22.4 CB technical data
- 22.5 Equipment and Options
- 22.6 Spare parts and accessories
- 22.7 Important conversion data for non-SI units
- 22.8 Conversion table for gas inlet pressures, bar – psi
- 22.9 Dimensions CB 60
- 22.10 Dimensions CB 160
- 22.11 Dimensions CB 220
23. Contamination clearance certificate
- 23.1 For units located outside North America and Central America
- 23.2 For units in North America and Central America
Word-Lesezeichen
- OLE_LINK17
- OLE_LINK16
- OLE_LINK6
- OLE_LINK7
- OLE_LINK5
- OLE_LINK3
- OLE_LINK1
- OLE_LINK2
Leere Seite