Cabletron Systems 6A000/ZX-250 - Manual (Page 262)

I-2 SmartCell 6A000/ZX-250 Reference Manual
Index
C
CACParams switch attribute ..... 2-20 to 2-21
CACStat switch attribute ........... 2-22 to 2-23
cause codes
AAL parameters cannot be
supported
........................................... B-2
Access information discarded ........... B-2
Bearer capability not authorized ....... B-2
Bearer capability not implemented ... B-2
Bearer capability not presently
available
............................................ B-2
Call control block not found ............. B-3
Call rejected ...................................... B-1
Calling party number not set. ............ B-3
Destination out of order .................... B-1
Identified channel does not exist ...... B-2
Incompatible destination ................... B-2
Incorrect message length .................. B-2
Information element non-existent
or not implemented
......................... B-2
Internal resource error ....................... B-3
Invalid call reference value ............... B-2
Invalid endpoint reference ................ B-2
Invalid information element contents B-2
Invalid number format ...................... B-1
Invalid transit network selection ....... B-2
Link not active .................................. B-3
Link not found .................................. B-3
Mandatory information element is
missing
.............................................. B-2
Message not compatible with call
state
................................................... B-2
Message type non-existent or not
implemented
..................................... B-2
Network out of order ........................ B-2
No response from network ................ B-2
No response to connect ..................... B-2
No response to out-going call process B-2
No response to restart request ........... B-3
No route to destination ...................... B-1
No route to specified transit network B-1
No user responding ........................... B-1
No VPI/VCI available ....................... B-2
Normal cell clearing ......................... B-1
Normal, unspecified .......................... B-1
Number changed ............................... B-1
Protocol error, unspecified ................ B-2
Quality of Service unavailable .......... B-2
Recovery on timer expire .................. B-2
Requested VPI/VCI not available ..... B-1
Resource unavailable, unspecified .... B-2
Response to STATUS ENQUIRY .... B-1
SAP not active .................................. B-3
Service or option not available,
unspecified
........................................ B-2
Temporary failure ............................. B-2
Too many pending add party requests B-2
Unassigned number ........................... B-1
Unsupported combination of traffic
parameters
......................................... B-2
User busy .......................................... B-1
User cell rate not available ................ B-1
User cell rate unavailable .................. B-2
User rejects all calls with calling
line identification
.............................. B-1
VPI/VCI assignment failure .............. B-1
VPI/VCI pair is unacceptable ........... B-1
CCTm ...................................................2-175
Cell Memory Size .................................2-185
change default boot load image ................3-3
changing switch start-up behavior ............3-1
changing the boot load default .................3-1
Chnl DVT .............................................2-164
chpi ...........................................................3-3
clear
config ...............................................2-39
clear flash file system ...............................3-4
clear switch configuration ........................3-4
clfs ............................................................3-4
Client Address ........................................2-24
Client State .............................................2-24
Client Type .............................................2-30
ClientNumber ............2-24 , 2-28 , 2-30 , 2-35 ,
.......................... 2-56 , 2-58 , 2-61 , 2-64 , 2-66
command defined .....................................1-1
Common DRAM ..................................2-185
Community Name ..................................2-37
Config .....................................................2-39
Configuration Errors ...............................2-79
Configured VCI Bits ............................2-133
Configured VPI Bits .............................2-133
Conn SubId ............................... 2-149 , 2-177
ConnectionCompeteTime .......................2-84
ConnectMethod ................... 2-13 , 2-41 , 2-94
ConnId ...................................... 2-149 , 2-177
ConnType ................................. 2-148 , 2-178