Rockwell Automation FlexPak 3000 Power Module Version 4.2 - Manual (Page 11)

INTRODUCTION TO THE DRIVE
49’1340 e FlexPak 3000 2-3
2.2.3 Input Voltage and Frequency Ratings:
Nominal voltage for three-phase at terminals 1U, 1V, 1W and 2U, 2V, 2W
On units 25, 60, 150 A ...................................................... 200 - 500 VAC at 50 Hz
200 - 460 VAC at 60 Hz
On units 500 V, 250, 450, 800, 1200, 1600 and 2000 A .................... 200 - 500 VAC
On units 575 V, 60 Hz, 1600 A........................................................... 300 - 575 VAC
On units 690 V, 50 Hz, 1600 A........................................................... 300 - 690 VAC
Input voltage for Field Controller Supply (on FlexPak 25 - 800 A) ................ max. 415 VAC
Input voltage for Field Current Regulator Kit (Option) .................................. max. 460 VAC
Voltage variation ..................................................................... +10% and -10% of Nominal
Nominal line frequency ..................................................................................... 50 or 60 Hz
Frequency variation ................................................................................................. ± 2 Hz
Fan Supply Voltage and Current Consumption on Units 1200 - 2000 A
Three-phase input voltage
at terminals 5U, 5W, 5W ............................... ... 400 V, 50 Hz or. 460 V, 60 Hz, 1A
NOTE: On units 60 Hz, 1200 -2000 A in UL, cUL version the fan must be external protected
by the following, thermal magnetic circuit breaker:
Dierikon part No. 610.11.05, RA catalog No. 140M-C2E1316.
2.2.4 Regulator Supply Voltage and Power Consumption
Single-phase input voltage, via autotransformer ..................... 230 VAC at terminals 0, 230
or 115 VAC at terminals 0, 115
Power Consumption (including fan on type 150 - 800 A) ................................ max. 120 VA
Thermal magnetic protection by external circuit breaker
NOTE: On units with terminals 4U, 4V (without autotransformer) input voltage 230 VAC is
required.
2.2.5 Relay Output for Main Contactor
Relay MCR at terminals X1:5 and X1:6
Nominal contact rating at AC 230 V, cos phi = 0.5 .................................................. 330 VA
Maximum current ........................................................................................................... 3 A
2.2.6 DC Voltage Ratings:
Maximum permissible armature voltage Ua max at inductive voltage drop of Uk ≤ 4% per phase
and max. 10% line undervoltage. At Uk = 4 to 7% Ua max must be derated per 5%.
Ua nom is the recommended standard motor armature voltage for the selected line
voltage and operation mode.
Table 2-1: Armature voltage for various line voltages
AC Line Motoring operation (S-6 / S-6R) Regenerating operation (S-6R)
Voltage Armature Voltage Armature Voltage
UN Ua nom Ua max Ua nom Ua max
200 V 200 V 230 V 200 V 214 V
400 V 460 V 490 V 400 V 440 V
460 V 520 V 570 V 500 V 500 V
500 V 600 V 620 V 520 V 535 V
575 V 700 V 710 V 600 V 615 V
660 V 800 V 810 V 700 V 706 V
690 V 800 V 850 V 700 V 738 V
Field voltage ........................................................................ max. 90% of line input voltage
Protection by external fuses according to table 8-8.