Mocomtech CDM-QX User Manual

Page 73

CDM-Qx/QxL Multi-Channel Satellite Modem with DoubleTalk™ Carrier-in-Carrier®

Revision 7

Front Panel Operation

MN/CDMQX.IOM

5–7

Table 5-1. Prinicpal Menu Tree

Section

Title

Remarks

5.2 Opening

Screen

5.3 Main

Menu

Select: Config; Monitor; Test; Info; Save/Load; Utiity

5.4 Config

Select: Remote; Tx; Rx; Group; Frame; Interface; Ref; Mask; (CDM-QxL only) ODU

5.4.1

Config

→ Remote

Select: Local; Serial; Ethernet

5.4.2

Config

→ Tx

Select: FEC; Mod; Code; Data; Freq; On/Off; Pwr; Scram; Clk; Inv; Tx

5.4.3

Config

→ Rx

Select: FEC; Demod; Code; Data; Freq; Acq; Descram; Buf; Inv; Misc; CNC

5.4.4

Config

→ Group

Select: Modem; Redundancy

5.4.5

Config

→ Frame

Select: Unframed; EDMAC; EDMAC-2; D&I++

5.4.6

Config

→ Interface

Select: RS422; V.35; RS232; HSSI; G.703; QDI; None

5.4.7

Config

→ Ref

Select: Internal; 10MHz

5.4.8

Config

→ Mask

Select: Transmit; Receive; Reference; (CDM-QxL only) BUC; (CDM-QxL only) LNB

5.4.9

Config

→ ODU

(CDM-QxL only)

Select: BUC; LNB

5.5 Monitor

Select: Alarms; Rx-Params; Event-Log; Stats; AUPC; CNC; (CDM-QxL only) ODU

5.5.1

Monitor

→ Alarms

Select: Transmit; Receive; Unit; (CDM-QxL only) ODU

5.5.2

Monitor

→ Rx-Params Select: Eb/No, BER, ΔF, BUF, RSL

5.5.3

Monitor

→ Event-Log

Select: View; Clear-All

5.5.4

Monitor

→ Stats

Select: View; Clear-All; Config

5.5.5

Monitor

→ AUPC

(CDM-QxL only)

Framing is required for AUPC Monitor - Select: Remote Eb/No; Tx Power Increase

5.5.6

Monitor

→ CnC

Carrier in Carrier

® (CnC) indicates as Active or N ot Active

5.5.7

Monitor

→ ODU

(CDM-QxL only)

Select: ODU; LNB

5.6 Test

Select: Mode; BIST; Spec-Analyzer

5.6.1

Test

→ Mode

Select: Norm; IF Loop; Dig Loop; I/O Loop; RF Loop; Tx-CW; Tx-1,0

5.6.2 Test

BIST

Select: BERT-Config; BERT-Mon; BERT-Control

5.6.3 Test

Spec-Analyzer Select: Center-Freq; Span

5.7 Info

Select: Rem; Tx; Rx; Buffer; Frame; Interface; Mask; Ref; ID

5.8 Save/Load

Select: Save; Load

5.9 Utility

Select: RxBuffer; Clock; Ref; ID; Display; Firmware; FAST

5.9.1 Utility

RxBuffer

Select to Re-center buffer

5.9.2 Utility

Clock

Select to edit Real-Time Clock (Time and Date)

5.9.3 Utility

Ref

Select: Adjust; Warm-up Delay

5.9.4 Utility

Select to edit Circuit ID

5.9.5 Utility

Display

Select to adjust VFD brightness

5.9.6 Utility

Firmware

Select: Update-CPLD; Information; Select

5.9.7 Utility

FAST

Select: Base; Slot1; Slot2; Slot3; Slot4

For the purpose of clarity, only the right-hand display area (or menu screen) is visually depicted
throughout the remainder of this chapter.