H3C Technologies H3C S5830V2 Series Switches User Manual

Page 182

171

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr af1 group 1 byte-count 1

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr be group 1 byte-count 1

# Assign the other queues to the SP group on interface Ten-GigabitEthernet 1/0/1.

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr af2 group sp

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr af3 group sp

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr af4 group sp

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr ef group sp

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr cs6 group sp

[SwitchA-Ten-GigabitEthernet1/0/1] qos wrr cs7 group sp

[SwitchA-Ten-GigabitEthernet1/0/1] quit

# Enable byte-count WRR on interface Ten-GigabitEthernet 2/0/1.

[SwitchA] interface ten-gigabitethernet 2/0/1

[SwitchA-Ten-GigabitEthernet2/0/1] qos wrr byte-count

# Configure WRR on interface Ten-GigabitEthernet 2/0/1:

{

Assign 50% of the interface bandwidth to the FCoE traffic (traffic assigned to queue 1).

{

Assign 50% of the interface bandwidth to Ethernet data traffic (traffic assigned to queue 0).

[SwitchA-Ten-GigabitEthernet2/0/1] qos wrr af1 group 1 byte-count 1

[SwitchA-Ten-GigabitEthernet2/0/1] qos wrr be group 1 byte-count 1

# Assign the other queues to the SP group on interface Ten-GigabitEthernet 2/0/1.

[SwitchA-Ten-GigabitEthernet2/0/1] qos wrr af2 group sp

[SwitchA-Ten-GigabitEthernet2/0/1] qos wrr af3 group sp

[SwitchA-Ten-GigabitEthernet2/0/1] qos wrr af4 group sp

[SwitchA-Ten-GigabitEthernet2/0/1] qos wrr ef group sp

[SwitchA-Ten-GigabitEthernet2/0/1] qos wrr cs6 group sp

[SwitchA-Ten-GigabitEthernet2/0/1] qos wrr cs7 group sp

[SwitchA-Ten-GigabitEthernet2/0/1] quit

Configure FCoE:
# Configure the switch to operate in FCF mode.

[SwitchA] fcoe-mode fcf

# Create VSAN 100. Enable the fabric configuration function for VSAN 100 (this step is optional
because the fabric configuration function is enabled by default).

[SwitchA] vsan 100

[SwitchA-vsan100] domain configure enable

# Configure the domain ID as 2 for the switch in VSAN 100.

[SwitchA-vsan100] domain-id 2 preferred

Non-disruptive reconfiguration or isolating the switch may be performed. Continue?

[Y/N]:y

# Enable FSPF globally for VSAN 100.

[SwitchA-vsan100] fspf enable

[SwitchA-vsan100] quit

# Create VSAN 200. Enable the fabric configuration function for VSAN 200 (this step is optional
because the fabric configuration function is enabled by default).

[SwitchA] vsan 200

[SwitchA-vsan200] domain configure enable

# Configure the domain ID as 3 for the switch in VSAN 200.

[SwitchA-vsan200] domain-id 3 preferred