H3C Technologies H3C S5830V2 Series Switches - Manual (Page 177)

166
[SwitchA-Ten-GigabitEthernet1/0/1] port hybrid vlan 4001 tagged
# Configure VLAN 1001 as the PVID of Ten-GigabitEthernet 1/0/1.
[SwitchA-Ten-GigabitEthernet1/0/1] port hybrid pvid vlan 1001
# Enable STP on Ten-GigabitEthernet 1/0/1.
[SwitchA-Ten-GigabitEthernet1/0/1] stp enable
[SwitchA-Ten-GigabitEthernet1/0/1] quit
# Configure interface Ten-GigabitEthernet 2/0/1 as a hybrid port.
[SwitchA] interface ten-gigabitethernet 2/0/1
[SwitchA-Ten-GigabitEthernet2/0/1] port link-type hybrid
# Assign Ten-GigabitEthernet 2/0/1 to VLAN 1001 as an untagged member.
[SwitchA-Ten-GigabitEthernet2/0/1] port hybrid vlan 1001 untagged
# Assign Ten-GigabitEthernet 2/0/1 to VLAN 4002 as a tagged member.
[SwitchA-Ten-GigabitEthernet2/0/1] port hybrid vlan 4002 tagged
# Configure VLAN 1001 as the PVID of Ten-GigabitEthernet 2/0/1.
[SwitchA-Ten-GigabitEthernet2/0/1] port hybrid pvid vlan 1001
# Enable STP on Ten-GigabitEthernet 2/0/1.
[SwitchA-Ten-GigabitEthernet2/0/1] stp enable
[SwitchA-Ten-GigabitEthernet2/0/1] quit
# Configure interface Ten-GigabitEthernet 1/0/10 as a trunk port, and assign the interface to
VLAN 1001.
[SwitchA] interface ten-gigabitethernet 1/0/10
[SwitchA-Ten-GigabitEthernet1/0/10] port link-type trunk
[SwitchA-Ten-GigabitEthernet1/0/10] port trunk permit vlan 1001
# Enable STP on Ten-GigabitEthernet 1/0/10.
[SwitchA-Ten-GigabitEthernet1/0/10] stp enable
[SwitchA-Ten-GigabitEthernet1/0/10] quit
# Configure interface Ten-GigabitEthernet 2/0/10 as a trunk port, and assign the interface to
VLAN 1001.
[SwitchA] interface ten-gigabitethernet 2/0/10
[SwitchA-Ten-GigabitEthernet2/0/10] port link-type trunk
[SwitchA-Ten-GigabitEthernet2/0/10] port trunk permit vlan 1001
# Enable STP on Ten-GigabitEthernet 2/0/10.
[SwitchA-Ten-GigabitEthernet2/0/10] stp enable
[SwitchA-Ten-GigabitEthernet2/0/10] quit
# Create Layer 2 aggregate interface 1, and configure it to operate in dynamic aggregation
mode.
[SwitchA] interface bridge-aggregation 1
[SwitchA-Bridge-Aggregation1] link-aggregation mode dynamic
# Disable STP on Layer 2 aggregate interface 1.
[SwitchA-Bridge-Aggregation1] undo stp enable
[SwitchA-Bridge-Aggregation1] quit
# Assign ports Ten-GigabitEthernet 1/0/5 through Ten-GigabitEthernet 1/0/8 to Layer 2
aggregation group 1.
[SwitchA] interface ten-gigabitethernet 1/0/5
[SwitchA-Ten-GigabitEthernet1/0/5] port link-aggregation group 1
[SwitchA-Ten-GigabitEthernet1/0/5] quit