Comtech EF Data SNM-1001L - Manual (Page 285)

SNM-1001L Satellite Modem Revision 1
Remote Control Operation MN/SNM1001L.IOM
B–11
ASYNC
Transmit
Overhead
Baud Rate Command:
Response:
Status:
Response: >add/TOBR_nnnnn'cr''lf']
>add/TOBR_nnnnn'cr''lf']
Where: nnnnn = 110, 150, 300, 600, 1200, 2400,
4800, 9600, 19200, or 38400.
Note: TX ASYNC Overhead only.
Transmit
Data Phase Command:
Response:
Status:
Response: >add/TDP_xxxx'cr''lf']
>add/TDP_xxxx'cr''lf'] Where: xxxx = NRM (normal data phasing), INV
(inverted data phasing).
Receive
Data Phase
Command:
Response:
Status:
Response: >add/RDP_xxxx'cr''lf']
>add/RDP_xxxx'cr''lf']
Where: xxxx = NRM (normal data phasing), INV
(inverted data phasing).
CTS Delay
Time Command:
Response:
Status:
Response: >add/CTSD_xx'cr''lf']
>add/CTSD_xx'cr''lf'] Where: xx = 0 to 60 (number of seconds).
B.3.4 System Configuration Commands
Time Of
Day Command:
Response:
Status:
Response: >add/TIME_hh:mmxx'cr''lf']
>add/TIME_hh:mmxx'cr''lf'] Where:
hh = 1 to 12 (hours).
mm = 00 to 59 (minutes).
xx = AM or PM.
Date
Command:
Response:
Status:
Response: >add/DATE_mm/dd/yyyy'cr''lf']
>add/DATE_mm/dd/yyyy'cr''lf'] Where:
mm = 1 to 12 (month).
dd = 1 to 31 (day).
yyyy = 00 to 99 (year) in 2 - digit year mode, and 1975
to 1999 and 2000 to 2075 in 4 - digit mode.
Remote Command:
Response:
>add/REM_'cr''lf'] Configures the modem for remote operation.
The SDM300L will respond to any status request at any
time. However, the SDM300L must be in 'Remote Mode'
to change configuration parameters.
Clear
Stored
Faults Command:
Response:
>add/CLSF_'cr''lf'] This command is used to clear all stored faults logged by
the SDM300L.
Modem
Operation
Mode Command:
Response:
Status:
Response: >add/MOM_xxxxxxx'cr''lf']
>add/MOM_xxxxxxx'cr''lf'] Where: xxxxxxx = TX_ONLY, RX_ONLY, or DUPLEX.
This command configures the modem for simplex or
duplex operation modes. When transmit only mode is
selected, receive faults are inhibited and when receive
only mode is selected, transmit faults are inhibited.
System
Modem
Type Command:
Response:
Status:
Response: >add/SMT_xxxxxxx'cr''lf']
>add/SMT_xxxxxxx'cr''lf'] Where: xxxxxx = AUPC, EFD, or CUSTOM.
Save
Modem
Config. Command:
Response:
>add/SMC_n'cr''lf'] Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command saves the current modem configuration for
recall at a later time using the 'RMC_' command. Up to
five different modem configurations can be saved.
Recall
Modem
Config. Command:
Response:
>add/RMC_n'cr''lf']
Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command causes the modem to be reprogrammed
with configuration parameters previously saved using the
'SMC_' command. One of five saved configurations can
be specified.