Yamaha LS9 User Manual
Page 72
72
Sending signals from MIX channels to the STEREO/MONO bus
LS9-16/32 Owner’s Manual
5
If you want to switch the on/off status of the
signal sent from the MIX channel to the
STEREO/MONO bus, or switch it between
ST/MONO mode and LCR mode, use either
of the following methods to access the TO
STEREO/MONO popup window.
• Move the cursor to the PAN popup button located in
the TO ST field of the SELECTED CH VIEW
screen, and press the [ENTER] key.
• Move the cursor to the TO ST PAN knob located in
the TO ST field of the SELECTED CH VIEW
screen, and press the [ENTER] key.
In the TO STEREO/MONO popup window you can
switch between ST/MONO mode and LCR mode in
sets of eight MIX channels, and change the on/off sta-
tus and pan/balance settings of the signals sent from
those channels to the STEREO/MONO bus. This
popup window shows the parameters for the eight
channels that include the MIX channel you selected in
step 3.
This popup window contains the following items.
1
Channel number / Channel name
This indicates the number and name of the channel
you’re operating.
B
MODE button
This button selects either ST/MONO mode or LCR
mode to specify how the signal is sent to the STEREO
bus and MONO bus. You can specify this mode indi-
vidually for each MIX channel. The setting will alter-
nate between the two modes each time you press the
button.
The currently selected mode is shown by the position
of the indicator (the green
◆ symbol) located immedi-
ately above the button.
C
ST button
D
MONO button
When the MODE button is set to ST/MONO mode,
these buttons act as individual on/off switches for the
signal sent from that MIX channel to the STEREO bus
and MONO bus.
E
TO ST PAN/TO ST BALANCE knob
For monaural MIX channels, this acts as the PAN
knob that adjusts the left/right panning of the signal
sent to the STEREO bus.
For stereo MIX channels, this acts as the BALANCE
knob that adjusts the volume of the left and right sig-
nals sent to the STEREO bus.
Move the cursor to the knob and use the dial or the
[DEC]/[INC] keys to adjust the setting.
For channels whose MODE button is set to LCR
mode, the following button and knob are shown
instead of the ST button (
3
) and MONO button (
4
).
F
LCR button
This button is an on/off switch for all signals sent from
that MIX channel to the STEREO bus and MONO
bus. If you turn off the button, no signals will be sent
from that output channel to the STEREO bus or
MONO bus.
G
CSR knob
This knob adjusts the proportion between the signal
level sent from that MIX channel to the STEREO (L/
R) bus and the level sent to the MONO (C) bus, over a
range of 0–100%. To adjust the setting, move the cur-
sor to the knob, press the [ENTER] key, and use the
dial or the [DEC]/[INC] keys.
6
Use the MODE button to select either ST/
MONO mode or LCR mode for each MIX
channel.
7
The ST button and MONO button are on/off
switches for the signal sent from the MIX
channel to the STEREO bus and MONO
bus.
8
If you want to use the STEREO bus, make
sure that the [ON] key of the STEREO chan-
nel is turned on in the top panel STEREO
MASTER section, and raise the fader of the
STEREO channel to an appropriate posi-
tion.
3
5
4
2
1
• If you’ve turned on POPUP APPEARS WHEN PRESSING
KNOBS in the PREFERENCE popup window (
can also access the above popup window by pressing the
SELECTED CHANNEL section [PAN] encoder.
HINT
6
7