Yokogawa Standalone MW100 User Manual
Mw100 communication command manual
Table of contents
Document Outline
- How to Use This Manual
- Contents
- Chapter 1 Commands
- 1.1 Command Format
- 1.2 List of Commands
- 1.3 Parameters
- Channel Numbers and Channel Ranges
- Upper and Lower Limit of Span (Measurement Channels)
- Upper and Lower Limit of Span (MATH Channels)
- Upper and Lower Limit of Scaling
- Alarm Types
- Alarm Value Setting Range
- Hysteresis Value Setting Range
- MATH Constants and Communication Input Values
- Channel Structure
- Point Structure
- Action Types
- Byte Output Order
- Measurement Interval and MATH Interval
- User Specified Strings
- Password String
- Host Name and Domain Name String
- File Name and Folder Name String
- 1.4 Setting Commands (System Related)
- 1.5 Setting Commands (Display Related)
- 1.6 Setting Commands (Communication Related)
- 1.7 Control Commands
- 1.8 Output Commands
- Chapter 2 Response
- 2.1 Response Format
- 2.2 ASCII Output
- Responses to Queries
- Output of the Latest Measured/Computed Data
- Output of the Latest Output Data
- Output of Setting Data
- Output of Decimal Place and Units
- Output of Operation Error Logs (FL0, ERROR)
- Output of Recording Logs (FL0, RECORD)
- Output of Recording Status Logs (FL0, RECSTATUS)
- Output of Alarm Summaries (FL0, ALARM)
- Output of Message Summaries (FL0, MESSAGE)
- Output of Communication Logs (FL0, COM)
- Output of FTP Client Logs (FL0, FTP_C)
- Output of Mail Client Logs (FL0, SMTP)
- Output of DHCP Client Logs (FL0, DHCP)
- Output of Time Synchronization Logs (FL0, SNTP)
- Output of FTP Server Logs (FL0, FTP_S)
- Output of HTTP Server Logs (FL0, HTTP)
- Output of Modbus Master Logs (FL0, MODBUS_M)
- Output of Modbus Master Command Status (FL1, MODBUS_MC)
- Output of Modbus Master Connection Status (FL1, MODBUS_MS)
- Output of Modbus Slave Log (FL0, MODBUS_S)
- Output of Modbus Client Logs (FL0, MODBUS_C)
- Output of Modbus Client Command Status (FL1, MODBUS_CC)
- Output of Modbus Client Connection Status (FL1, MODBUS_CS)
- Output of Modbus Server Log (FL0, MODBUS_T)
- Output of CIP Server Log (FL0, CIP)(Firmware version R3.02 or later)
- Output of PCCC Slave Log (FL0, PCCC)(Firmware version R3.02 or later)
- Output of MATH Status (FL0, MATH)
- Output of Operation Logs (FL0, CMD)
- Output of Strain Input Initial Balancing Result (FL1, BALANCE)
- Output of Status Information (IS)
- Output of Relay Status (VF)
- Output of System Recognition Status (CF)
- Output of Media Free Space (ME0)
- Output of File Information (ME1)
- 2.3 Binary Output
- Chapter 3 EtherNet/IP
- Appendix
- Appendix 1 Serial Interface (Optional) Specifications
- Appendix 2 Modbus Protocol
- Appendix 3 Modbus Communication Timeout
- Appendix 4 Bit Structure of Status Information
- Appendix 5 ASCII Character Codes
- Appendix 6 Maintenance/Diagnostic Server
- Appendix 7 Error Display on the 7-Segment LED and Corrective Actions
- Appendix 8 Detailed Explicit and I/O Messaging using RSLogix
- Appendix 9 Detailed Configuration of DigiOne IAP Serial Gateway
- Index