Watlow EZ-ZONE PM User Manual
Page 60
Watlow EZ-ZONE
®
PM Limit Controller
•
57
•
Chapter 6 Setup Page
Setup Page
Dis-
play
Parameter Name
Description
Range
Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Pro-
fibus
Index
Param-
eter ID
Data
Type
&
Read/
Write
[A;dSP]
[A.dSP]
Alarm (1 to 4)
Alarm Display
Display an alarm mes-
sage when an alarm is
active.
[`oFF]
Off (62)
[``on]
On (63)
On
Instance 1
Map 1 Map 2
1510
1910
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
0x6D (109)
1 to 4
0x10 (16)
30
9016
uint
RWES
[`A;dL]
[ A.dL]
Alarm (1 to 4)
Alarm Delay Time
Set the span of time
that the alarm will be
delayed after the pro-
cess value exceeds the
alarm set point.
0 to 9,999 seconds
0
Instance 1
Map 1 Map 2
1520
1920
Offset to next
instance (Map
1 equals +50,
for Map 2
equals +60)
0x6D (109)
1 to 4
0x15 (21)
31
9021
uint
RWES
[a;Clr]
[A.Clr]
Alarm (1 to 4)
Alarm Clear Request
*
Write to this register
to clear an alarm
Note:
If an alarm is setup
to latch when active
[a;Clr]
will appear
on the display.
`Clr]
Clear (0)
[ignr]
Ignore (204)
- - - -
Instance 1
Map 1 Map 2
1504
1904
Offset to
next instance
(Map1 1
equals +50,
Map 2 equals
+60)
0x6D
(109)
1 to 4
0xD (13)
- - - -
9013
uint
W
[a;sir]
[A.Sir]
Alarm (1 to 4)
Alarm Silence Re-
quest *
Write to this register
to silence an alarm
Note:
If an alarm is setup
to silence alarm
when active [a;sir]
will appear on the
display.
[`sil]
Silence (1010)
0
Instance 1
Map 1 Map 2
1506
1906
Offset to
next instance
(Map1 1
equals +50,
Map 2 equals
+60)
0x6D
(109)
1 to 4
0xE (14)
- - - -
9014
uint
W
[`a;st]
[ A.St]
Alarm (1 to 4)
Alarm State *
Current state of alarm
[`Str]
Startup (88)
[nonE]
None (61)
[`bLo]
Blocked (12)
[`AL;l]
Alarm low (8)
[`AL;h]
Alarm high (7)
[`Err]
Error (28)
- - - -
Instance 1
Map 1 Map 2
1496
1896
Offset to
next instance
(Map1 1
equals +50,
Map 2 equals
+60)
0x6D
(109)
1 to 4
9
- - - -
9009
uint
R
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read
with other interfaces.
*
These parameters/prompts are available in this menu with firmware revisions 11.0 and
above.
R: Read
W: Write
E:
EEPROM
S:
User Set