Paradyne JetFusion Integrated Access Device User Manual
Jetfusion, Integrated access device
Table of contents
Document Outline
- Notice
- Warranty, Sales, Service, and Training Information
- Document Feedback
- Trademarks
- Table of Contents
- Preface
- 1. Introduction
- 2. Quick Start Guide
- 3. Administration
- 4. WAN Configuration
- Basic WAN Setup Tasks
- Using the WAN Con figuration Menu
- Selecting the Datalink Protocol
- Setting Up TDM Voice
- Selecting the Physi cal Inter face
- Configur ing the G.SHDSL Interface
- Configur ing the SDSL Inter face- JF2100
- Configur ing the SDSL Inter face
- Configur ing the ADSL Inter face
- Setting the Interface to T1 or E1
- Configur ing the T1 Interface
- Configur ing the E1 Interface
- Configuring ATM PVCs
- Configuring ATM Options
- Configuring Frame Relay DLCIs
- Configuring Frame Relay Options
- Quick Con figuration
- 5. Router Configuration
- Basic Router Setup Tasks
- Router Configura tion Menu
- Configuring a Port IP Address
- Unconfig uring a Port IP Address
- Setting the Port Maxi mum Transmis sion Unit
- Enabling and Dis abling RIP
- Managing Static and Default Routes
- Setting the Default Route
- Configur ing DNS Client
- Configur ing DHCP Client
- Configur ing DHCP Relay
- Configur ing the Tel net Server Port
- Configur ing IP Fil tering
- Configur ing IP Header Compres sion (IPHC)
- Configur ing the LAN IP Broad cast Desti nation
- Displaying the Route Table
- 6. Bridge Configuration
- Basic Bridge Setup Tasks
- Bridge Configura tion Menu
- Enabling and Dis abling Bridging
- Setting the Bridge Aging Timer
- Enabling and Dis abling STP
- Configur ing Span ning Tree Bridge Pri ority
- Configur ing Span ning Tree Port Prior ity
- Configur ing Span ning Tree Hello Time
- Configur ing Span ning Tree Maximum Age
- Configur ing Span ning Tree Forward Delay
- Configur ing Span ning Tree Path Cost
- Deleting a Bridge For warding Database Entry
- 7. Voice Path Configuration
- Basic Voice Path Setup Tasks
- Voice Path Configura tion Menu
- Setting the Voice Gate way
- Setting Jit ter Delay
- Displaying Jitter Delay
- Setting Start Mode
- Setting SLIC Con trol Mode
- Setting Com pander Mode
- Set On Hook Transmis sion Mode
- Setting Idle Voltage Mode
- Setting Debug Mode
- Configur ing Echo Cancella tion
- Setting Loop Gain
- Setting Country Mode
- Managing MGCP Embedded Client
- Managing Copper- Com Call Control
- JetStream Call Con trol Set tings
- Configur ing AAL2/ LES CAS
- Configur ing AAL2/ LES CCS- ELCP
- 8. Firewall Configuration
- 9. DHCP Server Configuration
- Basic DHCP Server Setup Tasks
- The DHCP Server Configur- ation Menu
- Using DHCP Debugging Messages
- Enabling and Dis abling DHCP Server
- Enabling and Dis abling Checking for Addi tional DHCP Serv ers
- Configur ing DHCP Server Parameters
- Configuring the DHCP Address Range Pool
- Configur ing a DHCP Client Entry
- Displaying DHCP Server Details
- Displaying DHCP Server Sta tistics
- Displaying DHCP Server Assigned and Unas signed Addresses
- Displaying DHCP Entry Details
- Deleting a DHCP Cli ent Entry
- Deleting a DHCP Assign- ment Entry
- 10. Multicast Configuration
- Configur ing Multi cast
- Enabling and Dis abling Glo bal IP Multicast
- Configur ing PIM- Dense Mode by Port
- Managing Multicast Route Source
- Adding a Multicast Routing Source
- Removing a Multicast Routing Source
- Displaying the Multi cast Rout ing Source
- Displaying the IGMP Group
- Displaying the IGMP Querier
- Displaying the Multi cast Rout ing Table
- Displaying the PIM Neighbor
- 11. NAT Configuration
- The NAT Configuration Menu
- Enabling NAT Translation
- Configuring NAT Local Server
- Configuring NAT Timeouts
- Configuring the NAT Port Range
- Configuring the NAT Alias Entry
- NAT Statistics
- NAT Connection Table
- NAT Connection Details
- NAT Local Server Table
- NAT Alias Table
- Deleting IP Addresses from NAT Tables
- Deleting a NAT Local Server Entry
- Deleting a NAT Alias Entry
- 12. IAD Reports
- The Report Menu
- Current Configur- ation Report
- Network Statistics Reports
- Interface Statistics Reports
- Media Sta tistics Reports
- Route Table Report
- ARP Table Report
- Bridge For warding Database Report
- Bridge Sta tus Report
- PPP Autho rization Entries Report
- System Uptime Report
- Memory Statistics Reports
- Zero All Statistics
- 13. Command Line Interface
- Intro- duction
- set wan stp bridge
- Command Line Interface Reference
- exit
- ping
- quit
- rename file
- reset system
- remove lan ip address
- set bridge global
- set bridge stp global
- set dhcp server enable
- set dhcp server gateway
- set dhcp server subnet
- set dhcp server dns
- set dhcp server netbios
- set dhcp server domain
- set dhcp server range
- set dns server address
- set ip default route
- set ip route
- set lan bridge
- set lan ip address
- set lan rip
- set lan stp bridge
- set mgcp bracketing
- set mgcp listening port
- set mgcp notified entity
- set mgcp signaling connection
- set mgcp signaling port
- set mgcp signaling tos
- set mgcp voice connection
- set mgcp voice tos
- set nat
- set sdsl speed
- set system defaults
- set wan atm ppp auth
- set wan atm vc
- set wan bridge
- set wan datalink
- set wan framerelay
- set wan ip address
- set wan stp bridge
- set wan rip
- show con figuration
- show dhcp server con figuration
- show ip routes
- tftp receive
- 14. Troubleshooting and Diagnostics
- 15. Verification
- A. Menu Map
- B. Country Codes
- C. JetFusion IAD Specifications
- D. Connector Pinouts
- E. Glossary
- Index