AMT Datasouth 41AY89AR777 User Manual
X l 4 0 0 series, Amidalasouth
This manual is related to the following products:
Table of contents
Document Outline
- AMiDalasouth
- XL 400 SERIES
- 1 GENERAL INFORMATION
- 2 OPERATION
- 2.1 INTRODUCTION
- 2.2 OPERATOR PANEL
- 2.3 USING THE OPERATOR PANEL
- 2.4 SETTING VALUE FEATURES
- 2.4.1 Feature 01 - BAUD RATES
- 2.4.3 Feature 03 AND 04 - TOP AND BOTTOM FORM MARGINS, (PERFORATION SKIPOVER)
- 2.4.4 Features 05 AND 06 - LEFT AND RIGHT MARGINS
- 2.4.6 Feature 08 - VERTICAL TABS
- 2.4.8 Feature 10 - NATIONALITY (Primary Character Set)
- 2.4.9 Feature 11 - VERTICAL PITCH SELECTION
- 2.4.10 Feature 13 - EMULATION MODE
- 2.4.12 Feature 24 - PAPER FEED SPEED
- 2.4.13 DOWNLINE PROGRAMMING OF FEATURE VALUE FEATURES
- 2.5 SETTING DISCRETE FEATURES
- 2.5.1 Feature 28 - PRINT INHIBIT
- 2.5.2 Feature 29 - EXPANDED CHARACTER PRINTING
- 2.5.3 Feature 30 - X-ON, X-OFF SYNCHRONIZATION PROTOCOL
- 2.5.4 Feature 31 - DTR SYNCHRONIZATION PROTOCOL
- 2.5.5 Feature 32 - PARITY (EIGHTH BIT CONTROL)
- 2.5.6 Feature 33 - ODD/EVEN PARITY SELECTION/EIGHTH BIT MARKING
- 2.5.7 Feature34-AUTOWRAP
- 2.5.8 Feature 35 - PRINT ON RECEIPT OF CARRIAGE RETURN
- 2.5.9 Feature 36 - AUTOMATIC LINE FEED
- 2.5.10 Feature 37 - AUTOMATIC CARRIAGE RETURN
- 2.5.11 Feature 38 - FORM FEED DEFEAT
- 2.5.12 Feature 39 - 6/8 LINES PER INCH
- 2.5.13 Feature 40 - PAPER OUT DETECTION OVERRIDE
- 2.5.14 Feature 41 - SHIFT OUT SELECTS DOUBLE WIDE PRINT (PRINTER MODE ONLY)
- 2.5.15 Feature 42 - ON LINE/OFF LINE POWER-UP
- 2.5.16 Feature 43 - SERIAL INTERFACE DISABLE
- 2.5.17 Feature 44 - AUTOMATIC PRINT DISABLE
- 2.5.18 Feature 45 - EXIT DOUBLE WIDE PRINT ON LINE TERMINATOR
- 2.5.19 Feature 46 - ESCAPE SEQUENCE DISABLE
- 2.5.20 Feature 47 - DISPLAY MODE
- 2.5.21 Feature 48 - SECONDARY CHARACTER SET ENABLE
- 2.5.22 Feature 49 - DS-180 GRAPHICS (ANADEX 9500/9501 COMPATIBLE)
- 2.5.23 Feature 51 - UNIDIRECTIONAL TEXT PRINTING
- 2.5.24 Feature 59 - HANDSHAKE ON BUSY
- 2.5.25 Feature 61 - EIGHTH BIT ENABLE
- 2.5.26 Feature 63 - ETX/ACKNOWLEDGE HANDSHAKING
- 2.5.27 Feature 66 - PARALLEL INTERFACE DISABLE
- 2.5.28 Feature 69 - DOWNLOADABLE CHARACTER ENABLE
- 2.5.29 Feature 70 - BAR CODE ENABLE
- 2.5.30 Feature 76 - MICRO MODE
- 2.5.31 Feature 96 - HIGH SPEED DOUBLE STRIKE PRINT
- 2.5.32 Feature 97 - BELL OVERRIDE
- 2.5.33 Feature 98 - FEATURE LISTING
- 2.5.34 Feature 99 - PRINT-TEST/ASCII RIPPLE PATTERN
- 2.5.35 DOWNLINE PROGRAMMING OF DISCRETE FEATURES
- 3 INTERFACING
- 4 PROGRAMMING
- 5 OPERATOR MAINTENANCE AND TROUBLESHOOTING
- APPENDIX A SPECIFICATIONS
- APPENDIX A - CONTINUED
- APPENDIX C DISPLAY MODE CHARACTERS
- APPENDIX E VALUE FEATURES
- APPENDIX F DISCRETE FEATURES
- APPENDIX G NLQ FONTS WIDTH TABLES
- APPENDIX H PROPRINTER OPTION
- APPENDIX H - CONTINUED
- APPENDIX H - CONTINUED
- APPENDIX H - CONTINUED
- APPENDIX Н - GERMANY EPSON
- XL 400 SERIES