Rockwell Automation Flex/WebPak 3000 DC Drive ControlNet, Network Communication Board, 915FK2101 User Manual
Page 89
Register Map for WebPak 3000 Drives
8-21
N11:77
POSITION
VERNIER
P.241
Output of the position major loop
N11:78
POS
LL
WLO
OUT
P.246
Value of the position loop lead/lag low frequency
N11:79
POS
LL
RATIO
OUT
P.247
Value of the position loop lead/lag ratio
N11:80
POS
PI
KP
OUT
P.248
Value of the position loop PI proportional gain
N11:81
POS
PI
WLD
OUT
P.249
Value of the position loop PI lead frequency
N11:82
POS
LOOP
ERROR
P.254
The difference between
POSITION
REFERENCE
(P.240)
and position feedback
N11:83
TEN
/
DANCER
FDBK
SCALED
P.489
Output of the tension/dancer feedback scaling block
N11:84
TENSION
ON
DIN
TP
P.498
0 =
OFF
, 1 =
ON
N11:85
TENSION
COMMAND
P.850
0 =
OFF
, 1 =
ON
N11:86
STALL
TENSION
COMMAND
P.899
0 =
OFF
, 1 =
ON
N11:87
TEN
TO
CURRENT
OUT
P.876
Output of the tension loop’s tension-to-current scaling
block
N11:88
TEN
PI
KP
OUT
P.879
Value of the tension loop PI proportional gain
N11:89
TENSION
VERNIER
P.856
Output of the tension major loop in counts
N11:90
TAPER
PERCENT
P.859
Percent reduction to be applied to the tension
reference from the taper function
N11:91
TEN
LOOP
ERROR
P.834
Difference between the tension ramp output and the
tension/current loop feedback signal
N11:92
TEN
RAMP
OUTPUT
P.842
Output of the tension major loop ramp block after
tension-to-current conversion
N11:93
TENSION
DEMAND
P.844
Output of the tension setpoint generator in counts
N11:94
ROLL
DIAMETER
P.865
Value of the calculated roll diameter in engineering
units
N11:95
NORM
ROLL
DIAMETER
P.131
Value of the roll diameter normalized at 1.000 at
EMPTY
CORE
DIAMETER
(P.830)
N11:96
DIAMETER
CALC
OUTPUT
P.132
Value of the calculated roll diameter normalized at
1.000 at
EMPTY
CORE
DIAMETER
(P.830)
N11:97
DIAMETER
ANALOG
P.821
Output of the diameter calculator scaled from zero at
empty core to 4095 at full roll diameter
N11:98
DIAMETER
/
TAPER
IN
TP
P.192
Value of the diameter/taper range input in counts after
gain and zero have been applied
N11:99
UNWIND
DIAMETER
IN
P.828
Analog signal of diameter/taper analog input when
DIAMETER
/
TAPER
SELECT
(P.870) is set to diameter.
N11:100
DIAMETER
SELECT
A
TP
P.495
0 =
OFF
, 1 =
ON
N11:101
DIAMETER
SELECT
B
TP
P.496
0 =
OFF
, 1 =
ON
N11:102
DIAMETER
RESET
TP
P.829
0 =
OFF
, 1 =
ON
N11:103
DIAMETER
RST
DIN
TP
P.497
0 =
OFF
, 1 =
ON
N11:104
NETW
COMM
STATUS
P.908
0 =
NOT
ACTIVE
, 1 =
ACTIVE
Table 8.2 – File N11:x (Drive Display Data (Read Only)) for WebPak 3000 Drives (Continued)
File
Address
Parameter Name
Parameter
Number
Description