Rockwell Automation FlexPak/WebPak 3000 DC Drive AutoMax Network Communication Board User Manual
Rockwell Automation Equipment
Table of contents
Document Outline
- AutoMax‰ Network Communication Option Board For Use With FlexPak‰ 3000 DC Drives and WebPak‰ 3000 DC Drives
- Chapter 1 Introduction
- Chapter 2 Installation
- Chapter 3 Drive Configuration
- Chapter 4 Programming
- Chapter 5 FlexPak 3000 Drives: Original Register Map
- Chapter 6 FlexPak 3000 Drives: Alternate Register Map
- Chapter 7 WebPak 3000 Drives: Register Map
- List of Figures
- List of Tables
- Chapter 1 Introduction
- 1.1 Before You Start
- 1.2 Where to Find Additional Information
- 1.3 Getting Assistance from Reliance Electric
- 1.4 Related Hardware and Software
- 1.5 AutoMax Network Option Board Description
- Chapter 2 Installation
- 2.1 Installing the Network Option Board
- Step 1. Turn off, lock out, and tag all incoming power to the drive.
- Step 2. Loosen the two (2) captive screws on the drive cover. Remove the cover.
- Step 3. Loosen the captive screw on the carrier. Swing open the carrier. See figure 2.1.
- Step 4. Remove the screws that attach the carrier shield to the carrier. See figure 2.2.
- Step 5. Remove the connector that attaches the shield ground wire to the drive power supply. Set the shield aside. See figure 2.3.
- Step 6. Position the Network Option board over the standoffs. Refer to figure 2.4.
- Step 7. Secure the Network Option board using three captive screws on the board.
- Step 8. Plug the option board ribbon cable into the Network Option board.
- Step 9. Re-attach the carrier shield ground wire to the drive power supply.
- Step 10. Re-attach the carrier shield to the carrier.
- Step 11. Close the carrier and fasten it with the captive screw.
- Step 12. Re-install the drive cover.
- Step 1. Turn off, lock out, and tag all incoming power to the drive.
- 2.2 Connecting the Drive to an AutoMax Network
- Step 1. Stop any application tasks that are running.
- Step 2. Use the Network Drop Cable (M/N 57C381) to connect to the Communications Passive Tap (M/N57C380).
- Step 3. If the drop is at the end of the coaxial cable system, it must be terminated. Terminate by connecting a 75-Ohm Terminating Load (M/N 45C71) to the remaining BNC connector on the passive tap.
- Step 4. Remove the lockout and tag. Apply power to the drive. If a problem is detected during diagnostics, a fault or alarm will occur. See your drive software manual for information on faults and alarms.
- Step 1. Stop any application tasks that are running.
- 2.1 Installing the Network Option Board
- Chapter 3 Drive Configuration
- 3.1 Setting Up the Drive for Network Communication
- Step 1. Connect the Network Option board to the network using a passive tap. See section 2.2.
- Step 2. Apply power to the drive.
- Step 3. Assign a valid AutoMax network drop number to the drive using parameter netw drop number (P.900). You must set this para...
- Step 4. Set the network connection type using netw connect type (P.910). This defines the scope of data that will be communicate...
- Step 5. Apply power to the AutoMax rack.
- Step 1. Connect the Network Option board to the network using a passive tap. See section 2.2.
- 3.2 Selecting a Network Reference Source
- 3.3 How the Drive Responds to a Loss of Network Communication
- 3.1 Setting Up the Drive for Network Communication
- Chapter 4 Programming
- 4.1 Selecting a Register Map (FlexPak 3000 Drives Only)
- 4.2 How the Control Source Selection Affects Data Transfers
- 4.3 About Network Transfer Rates
- 4.4 Setting Up Data Types That Can Be Transferred
- 4.5 Tune/Config Update Synchronization Flag
- This flag allows the network master application program to track when the drive has updated tunable and configurable inputs. By ...
- 1. Modifies the tunable and configurable register data in the appropriate network registers.
- 2. Sets the tune/config input enable flag.
- 3. Toggles the tune/config update synchronization flag.
- 4. Monitors the tune/config update synchronization flag loopback bit until it equals the value written in item 3, above.
- Table 4.1 - Synchronization Flag Register Locations (Alternate and Original Register Maps)
- This flag allows the network master application program to track when the drive has updated tunable and configurable inputs. By ...
- 4.6 Monitoring Unacceptable Parameter Values
- 4.7 Timing Requirements
- 4.8 Drive Ready Status Bit
- 4.9 Display of Parameter Values Over the AutoMax Network
- 4.10 Parameters That Are Not Accessible Over the AutoMax Network
- 4.11 Parameters That Are Only Available in the FlexPak Alternate Register Map
- 4.12 Settings for Analog and Frequency Outputs
- Chapter 5 FlexPak 3000 Drives: Original Register Map
- 5.1 Accessing the Original Register Map
- 5.2 Finding Data in the Original Register Map Tables
- Table 5.1 - Location of Information in the Original Register Map Tables
- Table 5.2 - FlexPak 3000 Original Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Runtime Signal Data (Drive Output Data) (Continued)
- Table 5.3 - FlexPak 3000 Original Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
- Table 5.4 - FlexPak 3000 Original Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Control/Reference Data (Drive Input Data)
- Table 5.5 - FlexPak 3000 Original Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Tunable Data (Drive Input Data)
- Table 5.6 - FlexPak 3000 Original Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Configurable Data (Drive Input Data)
- Table 5.7 - FlexPak 3000 Original Register Map, Drop_2: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
- Table 5.8 - FlexPak 3000 Original Register Map, Drop_2: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
- Table 5.9 - FlexPak 3000 Original Register Map, Drop_2: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
- Table 5.10 - FlexPak 3000 Original Register Map, Drop_2: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data) (Continued)
- Table 5.11 - FlexPak 3000 Original Register Map, Drop_3: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
- Table 5.12 - FlexPak 3000 Original Register Map, Drop_3: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
- Table 5.13 - FlexPak 3000 Original Register Map, Drop_3: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
- Table 5.14 - FlexPak 3000 Original Register Map, Drop_3: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data)
- Table 5.15 - FlexPak 3000 Original Register Map, Drop_4: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
- Table 5.16 - FlexPak 3000 Original Register Map, Drop_4: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
- Table 5.17 - FlexPak 3000 Drop_4: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data)
- Table 5.18 - FlexPak 3000 Original Register Map, Drop_4: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data)
- Chapter 6 FlexPak 3000 Drives: Alternate Register Map
- 6.1 Accessing the Alternate Register Map
- 6.2 Diagnosing Processing Errors
- 6.3 Finding Data in the Alternate Register Map Tables
- The alternate register maps in table 6.3 through table 6.18 describe the registers and bits used by the FlexPak 3000 drive on the AutoMax network when netw register map sel (P.914) is set to alternate.
- Drop_2, Drop_3, and Drop_4 do not have master write registers for control/reference data. Drop_4 does not have a master read register for runtime signal data.
- Table 6.2 - Location of Information in the FlexPak 3000 Alternate Register Map Tables
- Table 6.3 - FlexPak 3000 Alternate Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Runtime Signal Data (Drive Output Data) (Continued)
- Table 6.4 - FlexPak 3000 Alternate Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
- Table 6.5 - FlexPak 3000 Alternate Register Map, Drop_1: Master Write Registers BASIC and FULL Connections. Control/Reference Data (Drive Input Data)
- Table 6.6 - FlexPak 3000 Alternate Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Tunable Data (Drive Input Data)
- Table 6.7 - FlexPak 3000 Alternate Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Configurable Data (Drive Input Data)
- Table 6.8 - FlexPak 3000 Alternate Register Map, Drop_2: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
- Table 6.9 - FlexPak 3000 Alternate Register Map, Drop_2: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
- Table 6.10 - FlexPak 3000 Alternate Register Map, Drop_2: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
- Table 6.11 - FlexPak 3000 Alternate Register Map, Drop_2: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data) (Continued)
- Table 6.12 - FlexPak 3000 Alternate Register Map, Drop_3: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
- Table 6.13 - FlexPak 3000 Alternate Register Map, Drop_3: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
- Table 6.14 - FlexPak 3000 Alternate Register Map, Drop_3: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
- Table 6.15 - FlexPak 3000 Alternate Register Map, Drop_3: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data) (Continued)
- Table 6.16 - FlexPak 3000 Alternate Register Map, Drop_4: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data)
- Table 6.17 - FlexPak 3000 Alternate Register Map, Drop_4: Master Write Registers FULL Connection. Tunable Data (Drive Input Data),
- Table 6.18 - FlexPak 3000 Alternate Register Map, Drop_4: Master Write Registers, FULL Connection. Configurable Data (Drive Input Data) (Continued)
- Chapter 7 WebPak 3000 Drives: Register Map
- 7.1 Using Indirect Parameters
- Example Using the ISR Word
- 7.1.1 Enabling the AutoMax Indirect Parameter Numbers
- Step 1. The tune/config input enable flag must have been cleared for a minimum of 600 msec (Drop_1, register 32, bit 14).
- Step 2. Modify AutoMax Indirect Register numbers (Drop_2, registers 32 to 63) with the parameter numbers that you wish to write to in the corresponding Drop_3 register. Parameter number 0 deactivates that particular indirect register.
- Step 3. Modify the corresponding register values (Drop_3, registers 32 to 63) for the parameters selected in step 2.
- Step 4. Set the tune/config input enable flag (Drop_1, register 32, bit 14).
- Step 5. Toggle the tune/config update synchronization flag (Drop_1, register 32, bit 15).
- Step 6. Monitor the tune/config update synchronization flag loopback bit in the Indirect Register Status word (Drop_3, register 32, bit 15) until it equals the value written in step 4.
- Step 1. The tune/config input enable flag must have been cleared for a minimum of 600 msec (Drop_1, register 32, bit 14).
- 7.1.2 Changing the AutoMax Indirect Register Values
- 7.1.3 Disabling the AutoMax Indirect Registers
- 7.2 Diagnosing Processing Errors
- 7.3 Finding Data in the Register Map Tables
- Table 7.2 - Location of Information in the WebPak Register Map Tables
- Table 7.3 - WebPak 3000 Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Runtime Signal Data (Drive Output Data) (Continued)
- Table 7.4 - WebPak 3000 Register Map, Drop_1: Master Read Registers, BASIC and FULL Connections. Tunable, Configurable, and Status Data (Drive Output Data) (Continued)
- Table 7.5 - WebPak 3000 Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Control/Reference Data (Drive Input Data) (Continued)
- Table 7.6 - WebPak 3000 Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Tunable Data (Drive Input Data)
- Table 7.7 - WebPak 3000 Register Map, Drop_1: Master Write Registers, BASIC and FULL Connections. Configurable Data (Drive Input Data)
- Table 7.8 - WebPak 3000 Register Map, Drop_2: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data)
- Table 7.9 - WebPak 3000 Register Map, Drop_2: Master Read Registers, FULL Connection. Tunable, Configurable, and Status Data (Drive Output Data)
- Table 7.10 - WebPak 3000 Register Map, Drop_2: Master Write Registers, FULL Connection. Tunable Data (Drive Input Data) (Continued)
- Table 7.11 - WebPak 3000 Register Map, Drop_3: Master Read Registers, FULL Connection. Runtime Signal Data (Drive Output Data) (Continued)
- Table 7.12 - WebPak 3000 Register Map, Drop_3: Master Write Registers, FULL Connection. Tunable/Configurable Data (Drive Input Data) (Continued)
- 7.1 Using Indirect Parameters
- Appendix A Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Original Map)
- Table A.1 - Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Original Map) (Continued)
- 1
- 10
- 0
- 1
- 23
- 4
- 26
- 1
- 13
- 2
- 1
- 13
- 1
- 1
- 16
- 1
- 40
- 1
- 0
- 8
- 1
- 13
- 1
- 32
- 9
- 1
- 32
- 10
- 1
- 30
- 1
- 63
- 1
- 16
- 2
- 0
- 1
- 17
- 2
- 2
- 3
- 0
- 3
- 16
- 3
- 40
- 3
- 17
- 3
- 41
- 2
- 19
- 2
- 41
- 2
- 18
- 2
- 63
- 2
- 20
- 2
- 42
- 1
- 18
- 4
- 1
- 4
- 33
- 4
- 51
- 4
- 32
- 1
- 19
- 4
- 2
- 4
- 35
- 4
- 34
- 2
- 22
- 2
- 44
- 2
- 23
- 2
- 45
- 4
- 45
- 4
- 52
- 4
- 53
- 4
- 46
- 4
- 54
- 3
- 18
- 3
- 61
- 3
- 19
- 3
- 42
- 3
- 20
- 3
- 43
- 3
- 31
- 1
- 10
- 9
- 1
- 5
- 2
- 27
- 2
- 48
- 2
- 28
- 2
- 49
- 2
- 21
- 3
- 54
- 1
- 6
- 1
- 10
- 6
- 3
- 30
- 3
- 49
- 1
- 26
- 1
- 51
- 1
- 25
- 1
- 50
- 1
- 27
- 1
- 52
- 3
- 3
- 1
- 0
- 10
- 4
- 22
- 8
- 4
- 22
- 5
- 1
- 15
- 1
- 10
- 5
- 1
- 56
- 3
- 24
- 4
- 22
- 3
- 1
- 0
- 11
- 4
- 22
- 7
- 1
- 17
- 1
- 41
- 4
- 50
- 0
- 4
- 48
- 4
- 50
- 1
- 4
- 49
- 1
- 0
- 3
- 1
- 0
- 0
- 1
- 0
- 1
- 1
- 0
- 1
- 0
- 5
- 4
- 27
- 4
- 41
- 1
- 0
- 2
- 1
- 10
- 1
- 32
- 8
- 1
- 32
- 2
- 4
- 22
- 6
- 1
- 61
- 3
- 15
- 3
- 57
- 1
- 10
- 1
- 4
- 29
- 4
- 28
- 4
- 42
- 3
- 33
- 1
- 22
- 3
- 5
- 3
- 56
- 3
- 35
- 3
- 34
- 1
- 37
- 3
- 4
- 1
- 12
- 3
- 36
- 3
- 39
- 3
- 38
- 3
- 37
- 1
- 0
- 4
- 1
- 32
- 4
- 1
- 20
- 4
- 3
- 4
- 56
- 4
- 55
- 4
- 59
- 4
- 57
- 4
- 58
- 4
- 0
- 0 - 4
- 1
- 10
- 8
- 1
- 0
- 9
- 2
- 56
- 4
- 22
- 2
- 1
- 55
- 3
- 21
- 1
- 32
- 3
- 2
- 15
- 2
- 40
- 4
- 22
- 1
- 1
- 53
- 2
- 14
- 1
- 14
- 4
- 21
- 0 & 1
- 4
- 37
- 4
- 60
- 4
- 36
- 4
- 39
- 4
- 61
- 4
- 38
- 4
- 22
- 9
- 3
- 12
- 3
- 58
- 1
- 19
- 1
- 43
- 1
- 32
- 11
- 1
- 18
- 1
- 42
- 1
- 13
- 0
- 3
- 55
- 3
- 13
- 3
- 59
- 3
- 14
- 3
- 60
- 1
- 10
- 4
- 2
- 58
- 1
- 21
- 1
- 45
- 1
- 29
- 1
- 57
- 1
- 28
- 1
- 62
- 1
- 34
- 1
- 35
- 1
- 36
- 1
- 58
- 1
- 59
- 1
- 60
- 1
- 10
- 14
- 1
- 7
- 1
- 8
- 1
- 9
- 1
- 33
- 4
- 23
- 4
- 62
- 4
- 24
- 4
- 63
- 2
- 33
- 2
- 60
- 2
- 38
- 2
- 39
- 2
- 37
- 1
- 21
- 2
- 12
- 2
- 52
- 2
- 54
- 2
- 53
- 2
- 51
- 2
- 11
- 2
- 35
- 2
- 34
- 2
- 36
- 2
- 59
- 2
- 55
- 1
- 10
- 13
- 1
- 10
- 7
- 4
- 30
- 4
- 43
- 4
- 31
- 4
- 44
- 1
- 32
- 7
- 1
- 10
- 9
- 1
- 0
- 12
- 4
- 25
- 4
- 40
- 2
- 57
- 1
- 20
- 1
- 44
- 3
- 1
- 3
- 22
- 3
- 62
- 3
- 23
- 3
- 63
- 4
- 22
- 4
- 1
- 31
- 2
- 17
- 2
- 62
- 1
- 32
- 0
- 1
- 46
- 2
- 16
- 1
- 10
- 10
- 1
- 10
- 3
- 1
- 32
- 3
- 26
- 3
- 45
- 3
- 25
- 3
- 44
- 3
- 28
- 3
- 47
- 3
- 2
- 1
- 3
- 3
- 29
- 3
- 48
- 3
- 27
- 3
- 46
- 1
- 4
- 1
- 24
- 1
- 49
- 1
- 23
- 1
- 48
- 1
- 2
- 1
- 1
- 1
- 32
- 1
- 22
- 0
- 4
- 22
- 1
- 54
- 2
- 30
- 2
- 29
- 2
- 50
- 1
- 10
- 2
- 1
- 10
- 12
- 1
- 0
- 14
- 1
- 0
- 15
- 1
- 0
- 13
- 2
- 13
- 2
- 61
- 2
- 26
- 2
- 47
- 2
- 31
- 1
- 22
- 1
- 47
- 2
- 24
- 2
- 25
- 2
- 46
- 1
- 32
- 14
- 1
- 0
- 6
- 1
- 32
- 15
- 1
- 0
- 7
- Table A.1 - Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Original Map) (Continued)
- Appendix B Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Alternate Map)
- Table B.1 - Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Alternate Map) (Continued)
- 1
- 23
- 1
- 40
- 2
- 1
- 1
- 0
- 8
- 1
- 13
- 1
- 32
- 9
- 1
- 32
- 10
- 1
- 10
- 0
- 1
- 13
- 1
- 1
- 13
- 2
- 1
- 63
- 1
- 16
- 1
- 17
- 3
- 0
- 3
- 16
- 3
- 40
- 3
- 17
- 3
- 41
- 2
- 19
- 2
- 41
- 2
- 18
- 2
- 63
- 2
- 20
- 2
- 42
- 1
- 18
- 4
- 33
- 4
- 51
- 4
- 32
- 1
- 19
- 4
- 35
- 4
- 34
- 2
- 22
- 2
- 44
- 2
- 23
- 2
- 45
- 4
- 45
- 4
- 52
- 4
- 52
- 4
- 53
- 4
- 46
- 4
- 54
- 3
- 18
- 3
- 61
- 3
- 19
- 3
- 42
- 3
- 20
- 3
- 43
- 3
- 31
- 1
- 10
- 9
- 1
- 5
- 2
- 27
- 2
- 48
- 2
- 28
- 2
- 49
- 2
- 21
- 3
- 54
- 1
- 6
- 1
- 10
- 6
- 3
- 30
- 3
- 49
- 1
- 51
- 3
- 7
- 1
- 50
- 3
- 6
- 3
- 53
- 5
- 2
- 51
- 3
- 8
- 3
- 3
- 1
- 1
- 6
- 1
- 26
- 8
- 1
- 26
- 5
- 1
- 15
- 1
- 10
- 5
- 1
- 56
- 3
- 24
- 1
- 26
- 3
- 1
- 1
- 1
- 1
- 26
- 7
- 2
- 2
- 1
- 41
- 4
- 47
- 4
- 50
- 0
- 4
- 48
- 4
- 50
- 1
- 4
- 49
- 1
- 1
- 14
- 1
- 0
- 3
- 1
- 0
- 0
- 1
- 0
- 1
- 1
- 0
- 1
- 1
- 1
- 0
- 5
- 4
- 27
- 4
- 41
- 1
- 0
- 2
- 1
- 10
- 1
- 32
- 8
- 1
- 32
- 2
- 1
- 26
- 6
- 1
- 61
- 3
- 15
- 3
- 57
- 1
- 10
- 1
- 4
- 29
- 4
- 28
- 4
- 42
- 3
- 33
- 1
- 22
- 3
- 56
- 3
- 35
- 3
- 34
- 1
- 37
- 3
- 51
- 3
- 4
- 1
- 12
- 3
- 36
- 3
- 39
- 3
- 38
- 3
- 37
- 1
- 1
- 0
- 1
- 0
- 4
- 1
- 20
- 4
- 56
- 4
- 55
- 4
- 59
- 4
- 57
- 4
- 58
- 1
- 32
- 4
- 1
- 1
- 8
- 1
- 1
- 9
- 1
- 1
- 10
- 1
- 1
- 11
- 1
- 1
- 12
- 1
- 10
- 8
- 1
- 0
- 9
- 2
- 56
- 1
- 26
- 2
- 2
- 54
- 1
- 32
- 3
- 2
- 15
- 2
- 40
- 1
- 26
- 1
- 2
- 14
- 2
- 52
- 1
- 14
- 4
- 37
- 4
- 60
- 4
- 36
- 4
- 39
- 4
- 61
- 4
- 38
- 1
- 0
- 11
- 1
- 0
- 12
- 1
- 26
- 9
- 3
- 12
- 3
- 58
- 1
- 43
- 2
- 4
- 1
- 32
- 11
- 1
- 42
- 2
- 3
- 1
- 13
- 0
- 3
- 55
- 3
- 13
- 3
- 59
- 3
- 14
- 3
- 60
- 1
- 1
- 15
- 1
- 10
- 4
- 3
- 53
- 0
- 2
- 58
- 1
- 45
- 2
- 6
- 3
- 52
- 1
- 28
- 1
- 62
- 1
- 34
- 1
- 35
- 1
- 36
- 1
- 58
- 1
- 59
- 1
- 60
- 1
- 29
- 1
- 10
- 14
- 1
- 7
- 1
- 8
- 1
- 9
- 1
- 33
- 4
- 23
- 4
- 62
- 4
- 63
- 4
- 63
- 1
- 57
- 2
- 60
- 2
- 38
- 2
- 39
- 2
- 37
- 1
- 21
- 1
- 53
- 1
- 55
- 1
- 54
- 1
- 52
- 3
- 53
- 1
- 2
- 11
- 2
- 35
- 2
- 34
- 2
- 36
- 2
- 59
- 2
- 55
- 3
- 53
- 2
- 1
- 10
- 13
- 1
- 10
- 7
- 4
- 30
- 4
- 43
- 4
- 31
- 4
- 44
- 1
- 32
- 7
- 1
- 10
- 9
- 1
- 0
- 10
- 4
- 25
- 4
- 40
- 2
- 57
- 1
- 44
- 2
- 5
- 3
- 1
- 3
- 22
- 3
- 62
- 3
- 23
- 3
- 63
- 1
- 26
- 4
- 2
- 33
- 1
- 31
- 2
- 17
- 2
- 62
- 1
- 32
- 0
- 1
- 46
- 2
- 16
- 1
- 10
- 10
- 1
- 10
- 3
- 1
- 32
- 3
- 26
- 3
- 45
- 3
- 25
- 3
- 44
- 3
- 28
- 3
- 47
- 3
- 2
- 1
- 3
- 3
- 29
- 3
- 48
- 3
- 27
- 3
- 46
- 1
- 4
- 2
- 32
- 1
- 39
- 1
- 49
- 2
- 9
- 1
- 48
- 2
- 8
- 1
- 32
- 6
- 1
- 2
- 2
- 0
- 1
- 38
- 1
- 32
- 1
- 1
- 26
- 0
- 1
- 26
- 3
- 53
- 3
- 2
- 53
- 2
- 29
- 2
- 50
- 1
- 10
- 2
- 2
- 43
- 1
- 10
- 12
- 1
- 1
- 13
- 1
- 1
- 7
- 1
- 1
- 3
- 1
- 1
- 4
- 1
- 1
- 2
- 1
- 1
- 5
- 2
- 13
- 2
- 61
- 2
- 26
- 2
- 47
- 2
- 31
- 1
- 47
- 2
- 7
- 2
- 24
- 2
- 25
- 2
- 46
- 1
- 32
- 14
- 1
- 0
- 6
- 1
- 0
- 7
- 1
- 32
- 15
- 1
- 32
- 5
- Table B.1 - Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Alternate Map) (Continued)
- Appendix C Cross Reference of Parameter Name to Drop and Register (WebPak 3000 Drives)
- Table C.1 - Cross Reference of Parameter Name to Drop and Register (WebPak 3000 Map)
- 2
- 32
- 2
- 33
- 2
- 34
- 2
- 35
- 2
- 36
- 2
- 37
- 2
- 38
- 2
- 39
- 2
- 40
- 2
- 41
- 2
- 42
- 2
- 43
- 2
- 44
- 2
- 45
- 2
- 46
- 2
- 47
- 2
- 48
- 2
- 49
- 2
- 50
- 2
- 51
- 2
- 52
- 2
- 53
- 2
- 54
- 2
- 55
- 2
- 56
- 2
- 57
- 2
- 58
- 2
- 59
- 2
- 60
- 2
- 61
- 2
- 62
- 2
- 63
- 3
- 32
- 3
- 33
- 3
- 34
- 3
- 35
- 3
- 36
- 3
- 37
- 3
- 38
- 3
- 39
- 3
- 40
- 3
- 41
- 3
- 42
- 3
- 43
- 3
- 44
- 3
- 45
- 3
- 46
- 3
- 47
- 3
- 48
- 3
- 49
- 3
- 50
- 3
- 51
- 3
- 52
- 3
- 53
- 3
- 54
- 3
- 55
- 3
- 56
- 3
- 57
- 3
- 58
- 3
- 59
- 3
- 60
- 3
- 61
- 3
- 62
- 3
- 63
- 2
- 15
- 1
- 25
- 1
- 41
- 1
- 14
- 1
- 30
- 1
- 63
- 2
- 0
- 2
- 1
- 2
- 16
- 2
- 17
- 1
- 5
- 1
- 7
- 2
- 2
- 2
- 18
- 1
- 52
- 1
- 51
- 2
- 19
- 1
- 6
- 2
- 20
- 1
- 16
- 1
- 56
- 3
- 24
- 2
- 3
- 1
- 42
- 2
- 22
- 2
- 31
- 1
- 40
- 2
- 23
- 1
- 18
- 2
- 24
- 2
- 4
- 2
- 25
- 1
- 11
- 1
- 61
- 2
- 26
- 2
- 28
- 1
- 24
- 1
- 38
- 2
- 5
- 1
- 13
- 2
- 28
- 1
- 21
- 2
- 31
- 2
- 29
- 2
- 6
- 2
- 30
- 3
- 0
- 3
- 1
- 3
- 2
- 3
- 3
- 3
- 4
- 1
- 56
- 1
- 15
- 3
- 5
- 3
- 6
- 1
- 17
- 3
- 7
- 1
- 44
- 1
- 43
- 1
- 46
- 3
- 8
- 1
- 29
- 1
- 62
- 1
- 34
- 1
- 35
- 1
- 36
- 1
- 58
- 1
- 59
- 1
- 60
- 3
- 9
- 1
- 8
- 1
- 9
- 1
- 10
- 1
- 33
- 3
- 7
- 3
- 8
- 1
- 22
- 1
- 23
- 1
- 28
- 3
- 10
- 3
- 11
- 3
- 12
- 3
- 13
- 3
- 14
- 3
- 15
- 1
- 39
- 3
- 9
- 1
- 45
- 3
- 10
- 1
- 31
- 3
- 16
- 1
- 47
- 1
- 32
- 3
- 11
- 1
- 3
- 3
- 12
- 1
- 4
- 1
- 50
- 1
- 49
- 1
- 2
- 3
- 17
- 3
- 18
- 3
- 19
- 3
- 20
- 3
- 21
- 3
- 22
- 3
- 23
- 1
- 0
- 1
- 1
- 1
- 27
- 1
- 57
- 2
- 24
- 1
- 37
- 2
- 25
- 2
- 26
- 1
- 54
- 1
- 53
- 2
- 27
- 2
- 28
- 3
- 13
- 1
- 55
- 1
- 19
- 3
- 14
- 1
- 20
- 2
- 29
- 1
- 48
- 2
- 30
- A
- B
- C
- D
- E
- F
- H
- I
- J
- L
- M
- N
- O
- P
- R
- S
- T
- U
- W
- Table C.1 - Cross Reference of Parameter Name to Drop and Register (WebPak 3000 Map)
- DIF Documentation Improvement Form