Rockwell Automation 1761-HHP-B30 MicroLogix 1000 with Hand-Held Programmer (HHP) - Manual (Page 530)

(HHP) User Manual
Index
MicroLogix
t 1000 with Hand-Held Programmer
I–26
First Instruction on Rung, 17–2
home, 4–7
menu, 4–9
mode, 4–10
multi-point function, 4–15
program monitor, 4–11
Start of File, 17–1
Start of Rung, 17–2
searching for specific addresses, 17–8
addresses that are displayed, 17–8
addresses you enter, 17–8
bit versus word addresses, 17–9
Selectable Timed Disable (STD), 13–17
entering the instruction, 13–17
example, 13–17
execution times, 13–17
function code, 13–17
instruction parameters, C–9
ladder representation, 13–17
using, 13–17
valid addressing modes, C–9
valid file types, C–9
Selectable Timed Enable (STE), 13–17
entering the instruction, 13–17
example, 13–17
execution times, 13–17
function code, 13–17
instruction parameters, C–9
ladder representation, 13–17
using, 13–17
valid addressing modes, C–9
valid file types, C–9
Selectable Timed Interrupt (STI) function
basic programming procedure, 13–15
Interrupt Subroutine (INT), 13–19
operation, 13–15
interrupt latency and interrupt
occurrences, 13–16
interrupt priorities, 13–16
status file data saved, 13–16
subroutine content, 13–15
overview, 13–15
Selectable Timed Disable (STD), 13–17
Selectable Timed Enable (STE), 13–17
Selectable Timed Start (STS), 13–18
STD/STE zone example, 13–17
Selectable Timed Start (STS), 13–18
entering the instruction, 13–19
execution times, 13–18
function code, 13–19
instruction parameters, C–10
ladder representative, 13–18
valid addressing modes, C–10
valid file types, C–10
Selecting Surge Suppressors, 1–7
selecting the language
using short-cut keys, 4–18
using the menu option, 4–17
Sequencer Compare (SQC), 13–6
entering parameters, 13–6
entering the instruction, 13–10
execution times, 13–6
function code, 13–10
instruction parameters, C–9
ladder representation, 13–6
operation, 13–11
using, 13–10
valid addressing modes, C–9
valid file types, C–9
sequencer instructions
overview, 13–6
effects on index register S:24, 13–6
entering the instructions, 13–6
Sequencer Compare (SQC), 13–6
Sequencer Load (SQL), 13–12
Sequencer Output (SQO), 13–6
Sequencer Load (SQL), 13–12
entering parameters, 13–12
entering the instruction, 13–13
execution times, 13–12
function code, 13–13
instruction parameters, C–9
ladder representation, 13–12
operation, 13–14
valid addressing modes, C–9
valid file types, C–9
Sequencer Output (SQO), 13–6
entering parameters, 13–6
entering the instruction, 13–8
execution times, 13–6
function code, 13–8
instruction parameters, C–9
ladder representation, 13–6
operation, 13–9
using, 13–7
valid addressing modes, C–9
valid file types, C–9
series logic (AND), 6–12
Set (SET), 8–8
entering the instruction, 8–9
execution times, 8–8
instruction parameters, C–9
ladder representation, 8–8
using, 8–9
valid addressing modes, C–9