Rockwell Automation 1761-HHP-B30 MicroLogix 1000 with Hand-Held Programmer (HHP) User Manual
Page 515
![background image](/manuals/579170/515/background.png)
MicroLogix
t 1000 with Hand-Held Programmer
Index
(HHP) User Manual
I–11
changing
editing modes, 17–3
radix, 18–30
remote controller modes, 18–21, 18–23
the baud rate, 19–6, 19–7
the HHP’s defaults, 4–17
the language, 4–17
the LCD display contrast, 4–18
the program defaults, 18–1
controller version, 18–18
extended I/O configuration bit, 18–8
fault override bit, 18–7
input filters, 18–12, 18–14, 18–15,
18–16
lock program function, 18–17
program name, 18–2
run always bit, 18–5
start-up protection bit, 18–6
STI enabled bit, 18–10
STI setpoint, 18–9
user and master passwords, 18–2
watchdog scan, 18–11
channel configuration
DF1 full–duplex, D–2
DF1 half-duplex slave, D–5
Clear (CLR), 10–11
entering the instruction, 10–11
execution times, 10–11
function code, 10–11
instruction parameters, C–3
ladder representative, 10–11
updates to arithmetic status bits, 10–11
valid addressing modes, C–3
valid file types, C–3
clearing a program
from a memory module, 19–5
from the controller, 5–2, 19–6
clearing faults, 20–12
CLR, Clear, 10–11
common procedures, 19–1
communication
DeviceNet, 3–13
establishing with controller, 3–12, 3–13,
19–7
types of, 15–1
communication protocols
DF1 full-duplex, D–2
DF1 half-duplex slave, D–4
DH-485, D–9
comparison instructions, 9–1
about, 9–2
Equal (EQU), 9–3
Greater Than (GRT), 9–7
Greater Than or Equal (GEQ), 9–8
Less Than (LES), 9–5
Less Than or Equal (LEQ), 9–6
Limit Test (LIM), 9–10
Masked Comparison for Equal (MEQ), 9–9
Not Equal (NEQ), 9–4
overview, 9–2
entering the instruction, 9–2
function codes, 9–3
using indexed word addresses, 9–3
configuring your program, 18–1
controller version, 18–18
extended I/O configuration, 18–8
fault override bit, 18–7
input filter settings, 18–12, 18–14, 18–15,
18–16
lock program function, 18–17
program name, 18–2
run always bit, 18–5
start-up protection, 18–6
STI enabled bit, 18–10
STI setpoint, 18–9
user and master passwords, 18–2
watchdog scan, 18–11
connecting blocks of logic
using ANB, 6–14, 8–12, 16–2
using ORB, 6–14, 8–12, 16–3
connecting the system
AIC+, 3–6
DeviceNet network, 3–13
DH-485 network, 3–3
HHP, 3–1
contact protection methods, 1–7
contacting Allen-Bradley for assistance, P–6
contactors (bulletin 100), surge suppressors
for, 1–9
contents of manual, P–2
continuous scan (CSN) mode, 18–22
control file (R), 6–4
controller
accessories and replacement parts, A–11
changing modes, 18–21
changing the baud rate, 19–6, 19–7
determining faults, 20–1
dimensions, A–7
fault messages, 20–13
features, 1–2
grounding, 2–1
installation, 1–1
mounting, 1–12