Rockwell Automation 1336Z SPIDER - FRN 2.xxx-5.xxx - Manual (Page 171)

Index I–3
Anlg Signal Loss, 7–30
Application Sts, 7–36
At Time, 7–29
Base Frequency, 7–58
Base Voltage, 7–58
Bidir In Offset, 7–64
Blwn Fuse Flt, 7–33
Boost Slope, 7–57
Braking Chopper, 7–14
Break Freq, 7–59
Break Frequency, 7–57
Break Voltage, 7–57
Bus Limit En, 7–14
Bus Reg Level, 7–26
Bus Regulation, 7–25
Clear Fault, 7–32
Cntrl Board Rev, 7–41
Common Bus, 7–15
Control Select, 7–56
CR Out Select, 7–28
Cur Lim Trip En, 7–32
Current Angle, 7–39
Current Limit, 7–9
Current Limit En, 7–10
Current Lmt Sel, 7–9
Current Step, 7–63
Data In, 7–47
Data Out, 7–47
DC Bus Memory, 7–40
DC Bus Voltage, 7–5
DC Hold Level, 7–13
DC Hold Time, 7–13
Decel Mask, 7–43
Decel Owner, 7–46
Decel Time, 7–8, 7–12
Dig At Temp, 7–28
Dig Out Current, 7–28
Dig Out Freq, 7–28
Dig Out Torque, 7–28
Direction Mask, 7–42
Direction Owner, 7–45
Drive Alarm, 7–36
Drive Direction, 7–38
Drive Status, 7–36
Drive Type, 7–41
Dwell Frequency, 7–19
Dwell Time, 7–19
EEPROM Cksum, 7–40
Enc Count Scale, 7–51
Encoder Counts, 7–51
Encoder Freq, 7–6, 7–51
Encoder Loss Sel, 7–51
Encoder PPR, 7–18, 7–49
Encoder Type, 7–49
ETM - Elapsed Time Meter, 7–7
Fault Alarms, 7–34, 7–35, 7–37
Fault Buffer, 7–32
Fault Data, 7–33
Fault Frequency, 7–34
Fault Mask, 7–43
Fault Owner, 7–46
Fault Status, 7–34
Firmware Ver., 7–41
Flt Clear Mode, 7–35
Flt Motor Mode, 7–33
Flt Power Mode, 7–33
Flux Amps Ref, 7–56
Flux Current, 7–7
Flux Up Time, 7–57
Flying Start En, 7–21
Freq Command, 7–5, 7–38
Freq Ref SqRoot, 7–17
Freq Select, 7–8, 7–16
Freq Source, 7–38
FStart Forward, 7–22
FStart Reverse, 7–22
Ground Warning, 7–35
Heatsink Temp, 7–6, 7–39
Hold Level Sel, 7–14
Input Mode, 7–8, 7–27
Input Status, 7–27, 7–37
IR Drop Volts, 7–57
Jog Frequency, 7–16
Jog Mask, 7–42
Jog Owner, 7–45
KI Process, 7–54
KP Amps, 7–15
KP Process, 7–55
Language, 7–21
Last Fault, 7–6
Latched Alarms, 7–37
Line Loss Fault, 7–32
Line Loss Mode, 7–22
Line Loss Volts, 7–24