A-77 – Yokogawa RotaMASS 3-Series User Manual

Page 177

APPENdIX 8. dEVICEVIEWEr WINdOW EXECUTEd FrOM FIELdMATE ANd PrM

a-77

IM 01R04B05-00E-E 3rd edition July 30, 2010 -00

Figure A8.3 Configuration (Mandatory)

Table A8.3 Configuration (Mandatory)

RB in o/S Mode(a-21)

alarm

Resource Block is in o/S mode. (a-21)
[Remedy]: Change the RB Block Mode.target(RB.MoDE_BLK.target) to auto mode.

tB in o/S Mode(a-22

alarm

transducer Block is in o/S mode. (a-22)
[Remedy]: Change the tB Block Mode.target(tB.MoDE_BLK.target) to auto mode.

aI1 in o/S Mode(a-23)

alarm

aI1 Block is in o/S mode. (a-23)
[Remedy]: Change the aI1 Block Mode.target(aI1.MoDE_BLK.target) to auto or other mode.
In addition, check that RB Block Mode.actual(RB.MoDE_BLK.actual) is set to auto mode.
If it is an unused function, set aLaRM_PERFoRM bit0 to 0.

aI2 in o/S Mode(a-24)

alarm

aI2 Block is in o/S mode. (a-24)
[Remedy]: Change the aI2 Block Mode.target(aI2.MoDE_BLK.target) to auto or other mode.
In addition, check that RB Block Mode.actual(RB.MoDE_BLK.actual) is set to auto mode.
If it is an unused function, set aLaRM_PERFoRM bit1 to 0.

aI3 in o/S Mode(a-25)

alarm

aI3 Block is in o/S mode. (a-25)
[Remedy]: Change the aI3 Block Mode.target(aI3.MoDE_BLK.target) to auto or other mode.
In addition, check that RB Block Mode.actual(RB.MoDE_BLK.actual) is set to auto mode.
If it is an unused function, set aLaRM_PERFoRM bit2 to 0.

aI4 in o/S Mode(a-26)

alarm

aI4 Block is in o/S mode. (a-26)
[Remedy]: Change the aI4 Block Mode.target(aI4.MoDE_BLK.target) to auto or other mode.
In addition, check that RB Block Mode.actual(RB.MoDE_BLK.actual) is set to auto mode.
If it is an unused function, set aLaRM_PERFoRM bit3 to 0.

Display out of Range(a-41)

alarm

Display value is out of range. (a-41)
[Remedy]: Change decimal point.

aI1 in Man Mode(W-21)

Warning

aI1 Block is in Man mode. (W-21)
[Remedy]: Change the aI1 Block Mode.target(aI1.MoDE_BLK.target) to auto or other mode.

aI2 in Man Mode(W-22)

Warning

aI2 Block is in Man mode. (W-22)
[Remedy]: Change the aI2 Block Mode.target(aI2.MoDE_BLK.target) to auto or other mode.

aI3 in Man Mode(W-23)

Warning

aI3 Block is in Man mode. (W-23)
[Remedy]: Change the aI3 Block Mode.target(aI3.MoDE_BLK.target) to auto or other mode.

aI4 in Man Mode(W-24)

Warning

aI4 Block is in Man mode. (W-24)
[Remedy]: Change the aI4 Block Mode.target(aI4.MoDE_BLK.target) to auto or other mode.

aI1 Simulation active(W-41)

Warning

aI1 Block is simulation mode. (W-41)
[Remedy]: Change the aI1 Simulation En/Disable(aI1.SIMuLatE.SIMuLatE_EnaBLE) to Disabled.

aI2 Simulation active(W-42)

Warning

aI2 Block is simulation mode. (W-42)
[Remedy]: Change the aI2 Simulation En/Disable(aI2.SIMuLatE.SIMuLatE_EnaBLE) to Disabled.

aI3 Simulation active(W-43)

Warning

aI3 Block is simulation mode. (W-43)
[Remedy]: Change the aI3 Simulation En/Disable(aI3.SIMuLatE.SIMuLatE_EnaBLE) to Disabled.

aI4 Simulation active(W-44)

Warning

aI4 Block is simulation mode. (W-44)
[Remedy]: Change the aI4 Simulation En/Disable(aI4.SIMuLatE.SIMuLatE_EnaBLE) to Disabled.