FEC MICRO NR - Manual (Page 13)

Chapter 9: Troubleshooting 9-1
9.1 Abnormal Conditions. 9-2
9.2 Torque Transducer Origin Error, Cal Check Error. 9-3
9.2.1 Code 1-0 Torque transducer / Zero Voltage error. 9-3
9.2.2 Code 1-1 Torque transducer / Cal Voltage error. 9-3
9.2.3 Code 1-2 Torque transducer / Zero check error. 9-3
9.2.4 Code 1-3 Torque transducer / Cal self-check error. 9-4
9.2.5 Code 1-4 Torque transducer / Started on Zero condition error. 9-4
9.2.6 Code 1-5 Torque transducer / Started on Cal condition error 9-4
9.2.7 Code 1-6 Torque transducer / Zero Level Self Check Error 9-4
9.3 Torque Over Abnormals 9-5
9.3.1 Code 2-1 Torque Over Abnormal / Torque Inhibit High Limit 9-5
9.4 Tool EEPROM Errors 9-6
9.4.1 Code 3-0 Preamplifier / Tool ID Checksum error 9-6
9.4.2 Code 3-1 Preamplifier / Tool type error 9-6
9.4.3 Code 3-2 Preamplifier / Started without tool connected 9-6
9.4.4 Code 3-3 Preamplifier / Tool is not connected 9-6
9.5 System Memory / Memory Card Errors 9-7
9.5.1 Code 4-1 system memory error / Flash ROM read error 9-7
9.5.2 Code 4-3 system memory card error / Card write error 9-7
9.6 Servo Amplifier Response / Resolver 9-8
9.6.1 Code 5-0 Servo Amplifier reply error / No reply from Resolver 9-8
9.7 Servo Type Error 9-9
9.7.1 Code 6-0 Servo Type error / Servo Type mismatch 9-9
9.8 Servo Amplifier Error 9-10
9.8.1 Code 8-1 Servo Amplifier error / Servo is over heated 9-10
9.8.2 Code 8-4 Servo Amplifier error / Over current 9-10
9.8.3 Code 8-5 Servo Amplifier error /Internal power supply 9-10
9.8.4 Code 8-6 Servo Amplifier error / Input Voltage abnormal 9-11
9.8.5 Code 8-9 Servo Amplifier error / Over speed. 9-11
9.8.6 Code 8-10 Servo Amplifier error / over load ( I square T) 9-11
9.8.7 Code 8-11 Servo Amplifier error / Resolver Signal Error 9-11
9.8.8 Code 8-12 Servo Amplifier error / Amplifier Parameter Error 9-12
9.8.9 Code 8-13 Servo Amplifier error / Amplifier Program Error 9-12
9.8.10 Code 8-15 Servo Amplifier error / PDU Error 9-12
9.8.11 Code 8-16 Servo Amplifier error / CPU Error 9-12
9.9 Parameter Error 9-13
9.9.1 Code 9-0 Parameter Error / Missing speed preset. 9-13
9.9.2 Code 9-1 Parameter Error/ Missing Speed or Time 9-13
9.9.3 Code 9-2 Parameter Error/ Parameter Select Error 9-13
9.9.4 Code 9-3 Parameter Error/ Missing Reverse Speed 9-13
9.9.5 Code 9-4 Parameter Error/ Torque Speed not set 9-13
9.9.6 Code 9-5 Parameter Error/ Torque Setup Error 9-14
9.9.7 Code 9-6 Parameter Error/ Angle Setup Error 9-14
9.9.8 Code 9-7 Parameter Error/ Reverse Torque over. 9-14
9.10 Micro-NR MNR Unit Fastening Faults and Causes 9-15
9.10.1 Accept Conditions 9-15
9.10.2 Reject Conditions 9-15