IDEC MicroSmart - Manual (Page 522)

x « FC4A M ICRO S MART U SER ’ S M ANUAL »
I NDEX
communication completion relay
M8080-M8116 25-6
M8117 25-6
number 25-7 , 25-8
SOTU and SOTD instructions 7-22
SOTU/SOTD instructions using with program
branching 18-2
source
and destination operands 8-5
operand 8-5
special
functions 1-2 , 5-1
input tab 5-11 , 5-12 , 5-18 , 5-20 , 5-22
special data registers 6-14
for analog potentiometers 5-30 , 6-15
for analog voltage input 5-31
for calendar/clock data 15-5
for data link communication error 25-4
for data link master/slave stations 6-15
for error information 29-3
for high-speed counter 5-7 , 5-8 , 5-9 , 5-10 , 6-15
for HMI module 6-15
for interrupt inputs 5-20
for modem mode 27-3
for port 2 6-16
for pulse outputs 6-15 , 20-4 , 20-17
for RS232C line control signals 17-29
for scan time 5-27
for timer interrupt 5-22
special internal relays 6-7
for calendar/clock data 15-6
for catch inputs 5-18
for data link communication 25-6
for expansion data registers 5-44
for high-speed counter 5-6 , 5-7 , 5-9 , 5-10
for interrupt inputs 5-20
for interrupt status 18-7
for modem mode 27-2
for timer interrupt 5-22
read only 6-8
read/write 6-7
specifications
AC input module 2-25
analog
I/O module 2-45
input 2-46 , 2-48 , 2-50
output 2-51
AS-Interface module 2-59
catch input 5-18
clock cartridge 2-68
communication
adapter 2-63
module 2-63
CPU module 2-4 , 2-14
data link 25-1
DC input
CPU module 2-6 , 2-16
input module 2-24
mixed I/O module 2-40
function 2-4 , 2-14
general 2-3 , 2-13 , 2-45
HMI module 2-60
memory cartridge 2-65
mixed I/O module 2-40
relay output
CPU module 2-7 , 2-18
mixed I/O module 2-41
output module 2-31
RS232C/RS485 converter 26-4
serial interface 26-4
single-phase high-speed counter 5-8 , 5-10
transistor
output CPU module 2-17
sink output module 2-33
source output module 2-36
two-phase high-speed counter 5-7 , 5-9
user communication mode 17-2
standard slaves 28-4
start
and result internal relays 27-2
control M8000 6-10
delimiter 17-18
WindLDR 4-5
start/stop
operation 4-3
schematic 4-3
using HMI module 5-39
using power supply 4-4
using WindLDR 4-3
status
code
intelligent module access 23-6
receive 17-23
transmit 17-11
data register modem mode 27-7
information 28-23
internal relays 28-23
internal relays 27-2
LED M8010 6-10
LEDs 28-16 , 28-17
relay 20-3 , 20-9 , 20-17 , 20-26
system 2-4 , 2-14 , 4-4
step response method 21-10
steps 30-3
stop
input 4-4 , 5-2
system status 2-4 , 2-14
stop access
read 23-4
write 23-5
STOP mode control signal status 17-29
STPA READ 23-4
STPA WRITE 23-5
strip direct mounting 3-7
structure of an advanced instruction 8-5
SUB 11-1
subroutine 18-4
subtraction 11-1
SwitchNet 1-8
data I/O port 28-35
slaves internal relays 28-37
system
program version D8029 6-17 , 29-1
requirements 28-2