Functional description – Artesyn ATCA-8330 Installation and Use (April 2015) User Manual
Page 108

Functional Description
ATCA-8330 Installation and Use (6806800S82B)
108
DSPx_USER_HW_CONF[3:0]
HW Strapping
DSP position on Mezzanine set by
strapping resistors range 0 - 11
0000 = DSP0
0001 = DSP1
0010 = DSP2
0011 = DSP3
All others are reserved.
DSPx_USER_HW_CONF[7:4]
Module_ID[3:0]
Mezzanine card position derived from
Module_ID[3:0]
0000 = DIMM Module0
0001 = DIMM Module1
0010 = DIMM Module2
0011 = DIMM Module3
0100 = DIMM Module4
0101 = DIMM Module5
0110 = DIMM Module6
0111 = DIMM Module7
1000 = DIMM Module8
1001 = DIMM Module9
All others are reserved.
DSPx_USER_HW_CONF[13:8]
HW Strapping
Strapped by resistor to 1
DSPx_USER_HW_CONF[14]
HW Strapping
0 = Unique factory-burned per-chip
MAC address (default)
1 = TFTP server with IP derived from
00:0C:90:02:
DSPx_USER_HW_CONF[15]
HW Strapping
0 = TFTP server at 192.168.1.200
(default)
1 = TFTP server with IP derived from
192.168.
BOOT_MODE[3:0]
HW Strapping
Strapped by resistor to 0100 = BOOTP
on EMAC 2 on SERDES 2
Table 5-2 DSP Control Signals (continued)
Signal Group
Controlled by
Description
- ARTM-9405 16x10GbE Installation and Use Guide (May 2014) (64 pages)
- ATCA 7370 / ATCA 7370-S Installation and Use (January 2015) (256 pages)
- ATCA 7370 / ATCA 7370-S Installation and Use (September 2014) (254 pages)
- ARTM-831X Installation and Use (June 2014) (346 pages)
- ATCA-7350 - Integrating with Workbench User Guide (September 2014) (34 pages)
- ATCA-7350 Installation and Use (September 2014) (208 pages)
- ATCA-7365-CE Installation and Use (May 2014) (294 pages)
- ATCA-7365-CE Installation and Use (May 2014) (306 pages)
- ATCA-7365-CE Installation and Use (Jan 2015) (300 pages)
- ATCA-7368 Installation and Use (June 2014) (222 pages)
- ATCA-7475 Installation and Use (October 2014) (284 pages)
- ATCA-7480 Installation and Use (April 2015) (330 pages)
- ATCA-8320 Installation and Use (May 2014) (456 pages)
- ATCA-9305 User's Manual (May 2014) (270 pages)
- ATCA-9405 Installation and Use (October 2014) (168 pages)
- ATCA-F120 Installation and Use (August 2014) (122 pages)
- ATCA-F140 Installation and Use (September 2014) (138 pages)
- ATCA-MF106 Installation and Use (September 2014) (86 pages)
- Centellis-4440/AXP1440 Installation and Use (September 2014) (208 pages)
- Centellis 4410 (AXP-1410) Installation and Use (July 2014) (202 pages)
- Centellis 2100 Release 3.0 Installation and Use (March 2015) (192 pages)
- Centellis 2100 Release 3.0 Installation and Use (March 2015) (176 pages)
- Centellis 2000 User Card-10GE Installation and Use (May 2014) (54 pages)
- Centellis 2000 User Card-10GE with Telco Alarm Installation and Use (May 2014) (60 pages)
- COMX-CAR-210 Installation and Use (August 2014) (76 pages)
- COMX-P1022 Installation and Use (July 2014) (84 pages)
- COMX-P2020 Installation and Use (February 2015) (100 pages)
- COMX-CORE Series Installation and Use (August 2014) (128 pages)
- COMX-P2020 Installation and Use (July 2014) (100 pages)
- COMX-P4080-2G-ENP2 Installation and Use (August 2014) (70 pages)
- COMX-P4080 Installation and Use (August 2014) (126 pages)
- COMX-P40x0 ENP2 Installation and Use (August 2014) (130 pages)
- COMX-P40x0 ENP2 Installation and Use (January 2015) (140 pages)
- iVPX7225 RTM Installation and Use (April 2015) (56 pages)
- MITX-430/MITX-440-DVI-2E Installation and Use (August 2014) (118 pages)
- CPCI-6200 Installation and Use (May 2015) (234 pages)
- SCP-MITX-CORE-820-SM Installation and Use (August 2014) (132 pages)
- iVPX7225 Installation and Use (April 2015) (168 pages)
- MVME2502 Installation and Use (August 2014) (150 pages)
- MVME2502 Installation and Use (December 2014) (166 pages)
- MVME2500 VxWorks 6.8 AMP User Guide (August 2014) (40 pages)
- MVME2500 VxWorks 6.8 User Guide (April 2014) (44 pages)
- MVME3100 Single Board Computer Installation and Use (June 2014) (156 pages)
- MVME4100 Single Board Computer Installation and Use (June 2014) (136 pages)