CANOGA PERKINS 9145E NID Software Version 3.0 - Manual (Page 54)

9145E NID Software User’s Manual Diagnostics
Latency/Jitter Test
40
Figure 4-3 Latency/Jitter Test Screen
Type the number of the function you wish to change, and press Enter. Once the settings have
been entered, select 12 and press Enter to begin or end testing. Press Esc to return to the
Diagnostics menu. Configuration items are as follows:
1. To IP Address - Enter the remote agent IP Address.
2. From IP Address - Select the originating IP address that the 9145E will place into the test
packets. Use Space to scroll through Auto Selection, Management IP, Test IP, and Aux IP.
The Auto Selection setting will start first with the Test IP. If the To IP Address is in the Test Network
Subnet, the Test IP will be used in the packet. If the Test IP is not available or the To IP Address is
not in the Test Network Subnet, the Aux IP is checked. If the Aux IP is not available or the To IP
Address is not the Aux Network Subnet, the Manager IP is used. Any address can be used with
the Manager IP since it has access to the Default Gateway.
If the From IP Address is specified as the Test IP or the Aux IP, and the To IP Address is not
located in the matching subnet, the destination is unreachable. An error message is displayed
when the Start Test command is given.
3. Test VLAN - The test packets will carry this VLAN Tag. The Test VLAN can only be changed
if the From IP Address is set to the Test IP, or the if Aux Allow Any VLAN is enabled.
4. Test Packets per sec - Controls the number of packets that will be sent for every second the
test runs. Settings are: 1, 2, 5, 10, 20, 50 or 100.
5. Packet Timeout sec (1 - 10) - Set the packet timeout for this test, from 1 to 10 seconds. If a
response is not received within this time limit, the packet will be considered dropped.
6. Packet Priority - Set packet Priority Code Point (PCP) from 0 to 7, with 0 being the highest
priority.
7. Packet DSCP Code (0 - 63) - The Differentiated Services Code Point (DSCP) code used to
classify packets in a Diffserv network. Other network devices that support Diffserv use the
Canoga Perkins Corp. Ethernet Network Interface Device 29-JAN-2009
Model 9145E-101-3-0 V43.08 F211 11:20:59
------------------------------------LATENCY/JITTER TEST------------------------
Test IP Addr/VLAN 0.0.0.0/0 Round Trip Packets 0
Test Duration 00:00 Dropped Packets 0
Minimum Latency (ms) 0.000000 Minimum Jitter (ms) 0.000000
Average Latency (ms) 0.000000 Average Jitter (ms) 0.000000
Maximum Latency (ms) 0.000000 Maximum Jitter (ms) 0.000000
Far End PBit Sent 0/Rcvd ? Local PBit Sent ?/Rcvd ?
Far End DSCP Sent 0/Rcvd ? Local DSCP Sent ?/Rcvd ?
1) To IP Addr 0.0.0.0 5) Packet Timeout sec (1-10) 3
2) From IP Addr Auto Selection 6) Packet Priority (0-7) 0
3) Test VLAN 0 7) Packet DSCP Code (0-63) 0
4) Test Packets per sec 1 8) Packet DF Bit Clear
9) Test Duration min:sec (0=forever) 0
10) Min Test Payload Size (40 - 9950) 40
11) Max Test Payload Size (40 - 9950) 40
12) Start/Stop Test
Select [1-12]:
------------------------------------Messages-----------------------------------